background image

036-21540-001-A-0503

Unitary Products Group

17

  

BLOWER SPEED ADJUSTMENT

The RPM of the supply air and condenser air blowers
will depend on the required CFM, and the static resis-
tance of both the supply/discharge and the return/
intake duct systems. With this information, the RPM for
the blowers can be determined from the blower perfor-
mance tables. Adjustment of blower speed is accom-
plished as follows:

1. Loosen belt tension by moving motor towards the 

blower shaft via the adjustable mounting.

2. Loosen the setscrew in the adjustable motor pulley 

flange. Remove key on pulleys 4-in. diameter and 
larger.

3. Blower speed will increase when moveable flange 

is adjusted towards the fixed flange (closed). 
Blower speed will decrease when the moveable 
flange is adjusted away from the fixed flange 
(opened). Pulleys are adjustable only in half-turn 
increments. Do not open pulley more than five full 
turns for "4L" and "A" belts, or six full turns for "B" 
belts.

4. Once the pulley has been opened/closed the 

appropriate numbers of turns, replace the external 
key and tighten the adjustment setscrew. Proper 
torque is 110-130 in.-lbs.

5. Install drive belts and adjust motor mount to ten-

sion belt.

TABLE 4: MOTOR AND PULLEY DATA

EVAPORATOR

 - STANDARD BLOWER MOTOR AND DRIVE DATA

Belts

HP

Frame

Eff.(%)

Pitch Dia.(in)

Browning #

Pitch Dia.(in)

Browning#

Rating / Size

Qty

3 TON

673-1010

1/3

56

68.0

2.0-3.0

1VP34 X 5/8

5.2

AK54H

4L370

1

4 TON

714-1071

1/2

56

75.0

2.0-3.0

1VP34 X 5/8

4.9

AK51H

4L370

1

5 TON

795-1193

3/4

56

75.0

2.0-3.0

1VP34 X 5/8

4.4

AK46H

4L360

1

8 TON

784-1045

1 1/2

145

84.0

3.0-4.0

1VP44 X 7/8

6.7

AK69H

4L380

1

10 TON

820-1094

2

145

84.0

3.0-4.0

1VP44 X 7/8

6.4

AK66H

4L370

1

12 TON

784-1045

2

145

84.0

3.0-4.0

1VP44 X 7/8

6.7

AK69H

4L370

1

15 TON

848-1064

5

184

87.5

4.7-5.9

1VP60 X 1-1/8

9.7

BK100H

B40

1

20 TON

848-1064

5

184

87.5

4.7-5.9

1VP60 X 1-1/8

9.7

BK100H

B50

1

25 TON

902-1082

7-1/2

213

88.5

5.0-6.0

1VP62 X 1-3/8

9.7

BK100H

BX51

1

EVAPORATOR

 - OVERSIZE BLOWER MOTOR AND DRIVE DATA

Belts

HP

Frame

Eff.(%)

Pitch Dia.(in)

Browning #

Pitch Dia.(in)

Browning#

Rating / Size

Qty

3 TON

897-1346

1/2

56

68.0

2.0-3.0

1VP34 X 5/8

3.9

AK41H

4L350

1

4 TON

946-1419

3/4

56

75.0

2.0-3.0

1VP34 X 5/8

3.7

AK39H

4L350

1

5 TON

946-1419

1

56

75.0

2.0-3.0

1VP34 X 5/8

3.7

AK39H

4L350

1

8 TON

972-1296

2

145

84.0

3.0-4.0

1VP44 X 7/8

5.4

AK56H

4L360

1

10 TON

1068-1364

3

145

86.5

3.6-4.6

1VP50 X 1-1/8

5.9

AK61H

A35

1

12 TON

984-1258

3

145

86.5

3.6-4.6

1VP50 X 1-1/8

6.4

AK66H

A36

1

15 TON

848-1064

5

184

87.5

4.7-5.9

1VP60 X 1-1/8

8.2

BK85H

B36

1

20 TON

1046-1287

7-1/2

213

88.5

5.2-6.4

1VP65 X 1-3/8

8.8

BK90H

BX50

1

25 TON

1033-1296

10

213

88.5

4.7-5.9

1VP60 X 1-3/8

15.7

BK160H

BX60

1

CONDENSER

 - STANDARD BLOWER MOTOR AND DRIVE DATA

Belts

HP

Frame

Eff.(%)

Pitch Dia.(in)

Browning #

Pitch Dia.(in)

Browning#

Rating / Size

Qty

3 TON

673-1010

1

143

82.5

2.0-3.0

1VP34 X 7/8

5.4

AK54H

4L400

1

4 TON

648-972

1

143

82.5

2.0-3.0

1VP34 X 7/8

5.4

AK56H

4L400

1

5 TON

771-1068

1 1/2

145

84.0

2.6-3.6

1VP40 X 7/8

5.9

AK61H

4L420

1

8 TON

761-1014

2

145

84.0

3.0-4.0

1VP44 X 7/8

6.9

AK71H

A65

1

10 TON

875-1118

3

182

86.5

3.6-4.6

1VP50 X 1-1/8

7.2

AK74H

A65

1

12 TON

685-875

3

184

86.5

3.6-4.6

1VP50 X 1-1/8

9.2

AK94H

A68

1

15 TON

794-974

5

184

87.5

4.4-5.4

1VP56 X 1-1/8

9.7

BK100H

B69

1

20 TON

717-882

7-1/2

213

87.5

5.2-6.4

1VP65 X 1-3/8

12.7

BK130H

B80

1

25 TON

717-882

7-1/2

213

87.5

5.2-6.4

1VP65 X 1-3/8

12.7

BK130H

B88

1

Adjustable

Motor Pulley

Fixed

Blower Pulley

Adjustable

Motor Pulley

Fixed

Blower Pulley

Drive Range

(RPM)

Motor

Adjustable

Motor Pulley

Model

Drive Range

(RPM)

Fixed

Blower Pulley

Model

Motor

Motor

Model

Drive Range

(RPM)

Содержание EMBASSY Series





















Отзывы: