[A.POWAER SETTING]
1 PWM Frequency
Drive frequency can be adjusted. At 2K, feeling of power at low speeds increases, and at 32K, feeling
of power at high speeds increases.
2 Punch
If you set it to 30, you can get the maximum punch when moving forward.
3 Compress
You can adjust the throttle curve. 0% is a linear slot.
4 Throtte Feel
Adjust throttle response. 5 is an aggressive throttle.
5 Max Reerse Force
You can adjust the maximum speed when moving backward.
[B.Brake Setting]
1 Drag Brake
Automatic brake adjustment when the transmitter throttle is in neutral. 30% is the maximum brake value.
2 Brake Punch
You can adjust the punch when braking. The maximum brake punch is 30%.
3 Initia Brake
You can adjust the effectiveness of the initial brake when operating the brake.
4 Brake Frequency
Smooth braking can be obtained by adjusting the brake frequency and increasing the frequency.
5 Max Breke Force
Throttle operation, maximum brake effectiveness adjustment.
[C.Timing Setting]
1 Boost Timing Activation
When you set the boost, you can select the automatic setting or the manual setting of the rotation speed.
2 Boost Timing
When increasing boost timing, this will increase the motor speed and reduce the torque. If boost
value has set too high, motor will become hot and may damage, so it is necessary to pay attention
to the motor temperature and make adjustments.
3 Boost Start RPM
Adjustment of boost start rotation speed.
4 Boost End RPM
Adjustment of boost end rotation speed.
5 Turbo Timing
The motor speed can be further increased when the transmitter is fully throttled. If turbo timing is
raised too high, motor will become hot and may be damaged, so it is necessary to pay attention to
the motor temperature and make adjustments.
6 Turbo Start
Timing of entering turbo will be adjusted, and if set to 50%, the timing of entering turbo will be earlier.
7 Turbo Delay
The time is adjusted while switching from boost to turbo, and if set to 0.00 seconds, it will switch
from boost to turbo without a time lag, but heat generated by the motor will also increase.
8 Turbo Up Rake
Will be able to adjust the amount of turbo timing increase in 0.5 second increments. Increasing value
may cause the motor to generate heat and cause damage. It is necessary to pay attention to motor
temperature and make adjustments.
9 Turbo Down Rake
Will be able to adjust the amount of turbo timing that drops when throttle is returned in 0.5 second
increments. Increasing value will cause the turbo timing to drop faster and the response will increase,
but if turbo value is large, it may cause a phenomenon like braking.
[D.General Setting]
1 Running Mode
Three types of operation settings can be set: forward / brake, forward / reverse, forward / reverse / brake.
2 Battery
Select the battery type.
3 Cut off Voltage
Set the battery cut voltage.
4 Esc Over Heat Protect
Will be able to adjust the ESC operating cut temperature for ESC protection.
5 Motor Over Heat Protect
To protect the motor, you can set the temperature to cut operation of ESC when motor temperature
rises too high. This will not work if motor does not have a temperature sensor. ..
6 Neutral Range
Neutral width adjustment.
7 BEC Voltage
Will be able to adjust the voltage input to the receiver. When adjusted to 7V, a servo that supports
high voltage is required.
8 Motor Action
Will be able to set the direction of rotation of the motor.
9 Motor Link
Will be able to change the motor wire connection order to A.B.C or C.B.A. If needed to change this,
check the ESC settings and connect the motor wire to his A.B.C terminal on the motor. There is a
risk of damage if connected incorrectly.
10 Remote Off
You can turn off the R160 esc when push and hold the brake to 100% over 8sec.
[E.Limit Vaiue]
1 Voltage Minimum
Minimum voltage during driving is displayed.
2 ESC temp Maximum
Maximum ESC temperature while driving is displayed.
3 Motor Tempreature maximum
Maximum temperature of motor while driving is displayed.
4 RPM Maximum
Maximum number of revolutions of motor while driving is displayed.
5 ClearLimit Record
Able to erase the data stored by ESC.
[F.Load Setting ]
1 Blinky Mode
Blinky mode and default setup.
2 Stock Mode
Stock mode and default setup.
3 Modify mode
Modify mode and default set. (Not included in R100)
4 Custom-1,2,3
Able to recall settings stored in Custom 1, 2, and 3. You can call it by pressing enter and then
pressing enter again.
[G.Save Setting]
1 Custom-1,2,3
Able to save 3 types of custom-configured data. Press enter and press enter again to save.
[H.FirmwareUpdete]
1 Load TF File
Able to update firmware stored on the SD card from your PC to ESC.
2 CurrentVersion
Able to check the current ESC version by pressing enter.
