YOKOGAWA VY Series Скачать руководство пользователя страница 3

Страница: 3 / 50

1. INTRODUCTION

Thank you for purchasing the Vortex Flowmeter

VY Series. This manual explains installation

and wiring of the Vortex Flowmeter VY Series.

Manuals explaining details regarding the

functional specifications, explanation of functions,

maintenance, and handling of each communication

specifications unique to each product can be

downloaded from the Yokogawa website. Be sure

to read these manuals to ensure correct use of the

products.

A printed version of the manual is also available for

purchase. For details, contact your nearest sales

office or Service Center.

Website address:

https://www.yokogawa.com/library/

■ Regarding This Manual

• This manual should be provided to the end

user.

• The contents of this manual may be changed

without prior notice.

• All rights are reserved. No part of this manual

may be reproduced in any form without

Yokogawa’s written permission.

• Yokogawa makes no warranty of any kind with

regard to this material, including, but not limited

to, implied warranties of merchantability and

suitability for a particular purpose.

• All reasonable effort has been made to ensure

the accuracy of the contents of this manual.

However, if any errors or omissions are found,

please inform Yokogawa.

• The specifications covered by this manual are

limited to those for the standard type under the

specified model number break-down and do not

cover custom-made instruments.

• Please note that this manual may not be

revised for any specification changes,

construction changes or operating part changes

that are not considered to affect function or

performance.

• Yokogawa assumes no responsibilities for this

product except as stated in the warranty.

• If the customer or any third party is harmed by

the use of this product, Yokogawa assumes

no responsibility for any such harm owing to

any defects in the product which were not

predictable, or for any indirect damages.

■ Safety and Modification Precautions

• When handling this instrument, follow the

safety precautions described in this document

for protection and safety of personnel, this

instrument and systems that incorporate this

instrument. Yokogawa does not guarantee the

safety of this instrument if the customer has

failed to comply with these precautions.

• Modification of the product in question without

the authorization of Yokogawa is strictly

forbidden.

• When an explosion protected type instrument

has been repaired or modified by the customer

and cannot be restored to its original condition,

the explosion protective structure of this

instrument will be impaired and a hazardous

condition will arise. Be sure to consult

Yokogawa regarding repairs and modifications.

The following safety symbol marks are used on this

product and in this manual.

WARNING

A WARNING sign denotes a hazard. It calls

attention to procedure, practice, condition or the

like, which, if not correctly performed or adhered

to, could result in injury or death of personnel. This

document presents precautions for avoiding such

hazards should such a situation arise.

CAUTION

A CAUTION sign denotes a hazard. It calls

attention to procedure, practice, condition or the

like, which, if not correctly performed or adhered

to, could result in damage to or destruction of the

product. This document presents precautions

for avoiding such hazards should there be a

physical risk to the user's well-being or damage to

equipment.

<1. Introduction>

IM 01F07A01-01EN

Содержание VY Series



















































Результаты поиска

Содержание VY Series

Отзывы:

Похожие инструкции для VY Series

Бренды по названию

Популярные бренды

YOKOGAWA VY Series, Руководство пользователя

Результаты поиска

Содержание VY Series

Отзывы:

Похожие инструкции для VY Series

Бренды по названию

Популярные бренды