YOKOGAWA UP35A Скачать руководство пользователя страница 7

IM 05P02D41-11EN  page 7/14

Contents

1.   Overview of Program Patterns

2.   Creating Program Patterns

3.   Program Pattern Setup Charts

1.  Overview of Program Patterns

The programming example given here demonstrates how to do the tasks outlined 

below.

1) Program the controller to start program operation at 50.0°C and raise the 

temperature up to 100.0°C in 50 minutes.

2) When the temperature reaches 100.0°C, keep it at this level for 30 minutes.

3) Raise the temperature up to 200.0°C in 60 minutes.

4) When the temperature reaches 200.0°C, keep it at this level for 30 minutes.

5) Lower the temperature to 50.0°C in 50 minutes.

6) When the temperature reaches 50.0°C, keep it at this level for 30 minutes.

PV input ranges are following:

Maximum value of PV input range: 250.0°C

Minimum value of PV input range: 0.0°C

PV input unit: C

Zone PID selection (ZON): Segment PID selection (0)

Segment setting method (SEG.T): Segment time setting (TIME)

Program time unit (TMU): hour.minute (HH.MM)

Seg.1

Seg.2

Seg.3

Seg.4

Seg.5

Seg.6

3

2

1

PV event 1

Segment time

TIME

Segment PID number

S.PIDN

100.0ºC

50.0ºC

200.0ºC

Time event 1

Time event 2

4

3

2

60 min.

30 min.

50 min.

30 min.

50 min.

30 min.

Time

Setpoint

TSP

TSP

TSP

The display symbols of the parameters, TSP (Final target setpoint), TIME (Segment 

time setting), and S.PID (Segmet PID number selection) are the same in each 

segment. However, the segment can be recognized by the number displayed on the 

Symbol display.

TSP

SSP

TSP

Dev. high (5ºC) PV high (110ºC)

On

On

On

On

On

Off

Off

Off

Off

Off

Off

Off

Off

Off

On

Dev. high (5ºC) PV high (210ºC) Dev. low (5ºC) PV low (10ºC)

See User's Manual for the Wait and Repeat actions, Zone PID, Start of program 

operation (Start code), Changing operation mode at segment switching (Junction 

code), Local mode.

Operation

Guide

Programming

UP35A/UP32A

Program Controller

Operation Guide

This operation guide describes basic program settings of the UP35A/UP32A.

For details of each function, see the electronic manual.

The scrolling guide is displayed on PV display in the Parameter Setting Display.

This guide can be turned on/off with the MODE key. (The scrolling guide is OFF when 

displaying the Program parameter setting display first.)

For details of the each function, refer to the electronic manual. Manuals can be 

downloaded or viewed at the following URL.

Functional

Enhancement

http://www.yokogawa.com/ns/ut/im/

«Standard Code Model»

2.  Creating Program Patterns

The following operating procedure describes an example of creating the program 

discussed in “1. Overview of Program Patterns.”

CAUTION

Before creating the program, reverify the PV Input Range, Program 

Time Unit (TMU), and Segment Setting Method (SEG.T) parameters.

If the setting of these setup parameter is changed, the program pat-

terns created and stored so far will be all cleared (initialized) !! Be 

careful.

PTNO.=1

SEGNO.=0

1.

2.

3.

4.

5.

Set the common parameter of the specified pattern.

When SEGNO.=0, set the common parameter for 

the pattern specified.

When SEGNO.=1 to 20 (40), set the parameter for 

the segment specified.

6.

7.

Starting target setpoint=50.0°C

STC=SSP (Starting target setpoint)

8.

Segment 1

Set the final target setpoint.

9.

10.

11.

Final target setpoint=100.0°C

Set the segment time.

Keep the initial value.

Pattern number

RST

lamp 

is lit.

Hold down the keys for 3 seconds.

Show the Operation Display.

MODE menu is displayed.

PROG menu is displayed.

Press the Right arrow key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Press the Down arrow key (until TSP appears.)

Press the Down arrow key.

Press the Down arrow key.

Set the final target setpoint.

Continues the TSP of segment 1.

12.

Set the segment PID number.

Keep the initial value.

Keep the initial value.

Set the junction code.

Segment time=50 minutes

13.

14.

15.

16.

Time event-2 starts from the Off state.

There is no the Off time.

Set the On time.

PV event-1 type=Deviation high limit

Set the PV event-1 type.

Set the PV event-1 setpoint.

17.

18.

PV event-1 setpoint=5.0°C

25.

Set the segment time.

19.

20.

21.

On time=25 minutes

22.

23.

24.

Segment 2

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the Up/Down arrow keys to move the 

parameters for segment-1 and the Left/Right 

arrow keys to move between each segments.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TIM1 appears.)

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TSP appears.)

Press the Down arrow key.

Time event-1 starts from the Off state.

●  Settings for the segment 3 to 6 can be done similarly.
●  For  Programming  and  the  settings  for  Wait  and  Repeat  actions, 

see User's Manual.

Set the junction code.

In this case, the former segment is left unchanged.

PV event-1 type=PV high limit

Set the PV event-1 type.

26.

Segment time=30 minutes

Segment PID number=2

27.

29.

30.

Set the segment PID number.

Set the PV event-1 setpoint.

32.

31.

28.

Start condition of time event 2=ON start

33.

PV event-1 setpoint=110.0°C

35.

Set the time event 2.

34.

36.

37.

Press the DISPLAY key once to return to the 

Operation Display.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TIM2 appears.)

Press the Down arrow key (until TIM1 appears.)

Change the Up/Down arrow keys to move the 

parameters for segment-1 and the Left/Right 

arrow keys to move between each segments.

Press the Down arrow key.

Time event-1 starts from the Off state.

PTNO.=1

SEGNO.=0

1.

2.

3.

4.

5.

Set the common parameter of the specified pattern.

When SEGNO.=0, set the common parameter for 

the pattern specified.

When SEGNO.=1 to 20 (40), set the parameter for 

the segment specified.

6.

7.

Starting target setpoint=50.0°C

STC=SSP (Starting target setpoint)

8.

Segment 1

Set the final target setpoint.

9.

10.

11.

Final target setpoint=100.0°C

Set the segment time.

Keep the initial value.

Pattern number

RST

lamp 

is lit.

Hold down the keys for 3 seconds.

Show the Operation Display.

MODE menu is displayed.

PROG menu is displayed.

Press the Right arrow key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Press the Down arrow key (until TSP appears.)

Press the Down arrow key.

Press the Down arrow key.

Set the final target setpoint.

Continues the TSP of segment 1.

12.

Set the segment PID number.

Keep the initial value.

Keep the initial value.

Set the junction code.

Segment time=50 minutes

13.

14.

15.

16.

Time event-2 starts from the Off state.

There is no the Off time.

Set the On time.

PV event-1 type=Deviation high limit

Set the PV event-1 type.

Set the PV event-1 setpoint.

17.

18.

PV event-1 setpoint=5.0°C

25.

Set the segment time.

19.

20.

21.

On time=25 minutes

22.

23.

24.

Segment 2

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the Up/Down arrow keys to move the 

parameters for segment-1 and the Left/Right 

arrow keys to move between each segments.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TIM1 appears.)

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TSP appears.)

Press the Down arrow key.

Time event-1 starts from the Off state.

●  Settings for the segment 3 to 6 can be done similarly.
●  For  Programming  and  the  settings  for  Wait  and  Repeat  actions, 

see User's Manual.

Set the junction code.

In this case, the former segment is left unchanged.

PV event-1 type=PV high limit

Set the PV event-1 type.

26.

Segment time=30 minutes

Segment PID number=2

27.

29.

30.

Set the segment PID number.

Set the PV event-1 setpoint.

32.

31.

28.

Start condition of time event 2=ON start

33.

PV event-1 setpoint=110.0°C

35.

Set the time event 2.

34.

36.

37.

Press the DISPLAY key once to return to the 

Operation Display.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TIM2 appears.)

Press the Down arrow key (until TIM1 appears.)

Change the Up/Down arrow keys to move the 

parameters for segment-1 and the Left/Right 

arrow keys to move between each segments.

Press the Down arrow key.

Time event-1 starts from the Off state.

PTNO.=1

SEGNO.=0

1.

2.

3.

4.

5.

Set the common parameter of the specified pattern.

When SEGNO.=0, set the common parameter for 

the pattern specified.

When SEGNO.=1 to 20 (40), set the parameter for 

the segment specified.

6.

7.

Starting target setpoint=50.0°C

STC=SSP (Starting target setpoint)

8.

Segment 1

Set the final target setpoint.

9.

10.

11.

Final target setpoint=100.0°C

Set the segment time.

Keep the initial value.

Pattern number

RST

lamp 

is lit.

Hold down the keys for 3 seconds.

Show the Operation Display.

MODE menu is displayed.

PROG menu is displayed.

Press the Right arrow key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Press the Down arrow key (until TSP appears.)

Press the Down arrow key.

Press the Down arrow key.

Set the final target setpoint.

Continues the TSP of segment 1.

12.

Set the segment PID number.

Keep the initial value.

Keep the initial value.

Set the junction code.

Segment time=50 minutes

13.

14.

15.

16.

Time event-2 starts from the Off state.

There is no the Off time.

Set the On time.

PV event-1 type=Deviation high limit

Set the PV event-1 type.

Set the PV event-1 setpoint.

17.

18.

PV event-1 setpoint=5.0°C

25.

Set the segment time.

19.

20.

21.

On time=25 minutes

22.

23.

24.

Segment 2

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the Up/Down arrow keys to move the 

parameters for segment-1 and the Left/Right 

arrow keys to move between each segments.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TIM1 appears.)

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TSP appears.)

Press the Down arrow key.

Time event-1 starts from the Off state.

●  Settings for the segment 3 to 6 can be done similarly.
●  For  Programming  and  the  settings  for  Wait  and  Repeat  actions, 

see User's Manual.

Set the junction code.

In this case, the former segment is left unchanged.

PV event-1 type=PV high limit

Set the PV event-1 type.

26.

Segment time=30 minutes

Segment PID number=2

27.

29.

30.

Set the segment PID number.

Set the PV event-1 setpoint.

32.

31.

28.

Start condition of time event 2=ON start

33.

PV event-1 setpoint=110.0°C

35.

Set the time event 2.

34.

36.

37.

Press the DISPLAY key once to return to the 

Operation Display.

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key. (Blinks during the change.)

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Press the SET/ENTER key.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value and the 

Left/Right arrow keys to move between digits.

Change the setpoint using the Up/Down arrow 

keys to increase and decrease the value.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key.

Press the Down arrow key (until TIM2 appears.)

Press the Down arrow key (until TIM1 appears.)

Change the Up/Down arrow keys to move the 

parameters for segment-1 and the Left/Right 

arrow keys to move between each segments.

Press the Down arrow key.

Time event-1 starts from the Off state.

Содержание UP35A















Отзывы: