YOKOGAWA TB830D Скачать руководство пользователя страница 27

Страница: 27 / 85

<2. INSTALLATION, PIPING, AND WIRING>

2-14

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

Power supply cable (E)

If a Terminal box is included, wire it to the Terminal box If there is no Relay box, wire it to the

Relay box.
Refer to Figure 2.14 for wiring. Cables for power supply and grounding must be provided by the

customer. Refer to “2.2.4 Power supply cable (E)”

for the specifications of the cable and the

requirements for power supply and grounding wiring.

Relay box control cable (F)

Dedicated cables are included. Connect to the specified connectors referring to

Figure 2.14,

Figure 2.15

, and Figure 2.16.

Solenoid valve cable (G)

Solenoid valve and its valve cabling must be provided by the customer. Refer to Table 2.2 and

Table 2.3

for required specifications. Wire solenoid valve cabling referring to

Figure 2.14 and

Figure 2.16. Use a solenoid valve that matches the required power supply voltage.

Table 2.2

Solenoid valve Requirements

Port

Valve type

Max. working

pressure

Max. working

pressure difference

SV1 (Measure)

15A

Motor Valve 3 Terminals

(Open

Shut

Common)

1 MPa

SV2 (Wash)

RC3/8

Solenoid valve NOOC.

(*1)

1.5 MPa

0.5 MPa

SV3 (Zero)

RC3/8

Solenoid valve NOOC.

(*1)

1.5 MPa

0.5 MPa

SV4 (Drain)

Ø21 × Ø18

Silicone tube

Pinch valve N.C. (*1)

―

*1:

The valve opens when energized.

Table 2.3

Solenoid valve Cable Requirements (Recommended Cables)

Cable length

1.2 m

Rated voltage

300 V AC

Specifications

SV1

AWG 17 3 core cable, M3 round terminal

SV2, SV3, SV4

AWG 20 2 core cable, M3 round terminal

2.3

Desiccant mounting

High humidity in detector internal storage may affect the measurement. Desiccants must be

installed on detector internal storage for correct readings.

With sampling system (-A1, -A2, -A3)

The desiccant is shipped pre-installed on detector internal storage, so you do not need to install

the desiccant when starting operation.

Without sampling system (-NN, -A5)

Desiccant must be attached to detector internal storage. Perform mounting of the desiccant

according to the following.

To prevent electric shock, turn off the power supply of the detector before turning mounting the

desiccant.

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 27 / 85

Результаты поиска

Содержание TB830D

Отзывы: