manualshive.com logo in svg

YOKOGAWA TB830D, Руководство пользователя, Страница: 26 / 85

Поделиться
Скачать
YOKOGAWA TB830D Скачать руководство пользователя страница 26

  

<2.  INSTALLATION, PIPING, AND WIRING>

2-13

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

  WARNING

Never let the power cables of TB830D (Figure 2.15) touch the Cable for Relay box control 

(F), SENCOM cable for turbidity/chlorine (A), resulting in failure to comply with the safety 

requirements.

  WARNING

The wiring must meet the IP65 or higher. The four screws of detector cover are tightened to 1.5 

N·m.

Ground Terminal

101

102

201

202

301

302

Solenoid valve cable (G)

FLXA402T power supply cable (B)

 

TB830D power supply cable (C)

View from the bottom

Relay box 

control cable (F)

Relay Box power supply cable (D)

 or power supply cable (E)

SV3 cable

SV2 cable

SV1 cable

SV4 cable

Figure 2.16 

Wiring of Relay box (for-A5)

n

  SENCOM cable for Turbidity/Chlorine (A)

Dedicated cables are included. Refer to Figure 2.14 and 

Figure 2.15

 for wiring. Refer to Section 

2.6.1 of FLXA402T Installation Manual (IM12A01G01-02EN) for the wiring on FLXA402T.

n

  FLXA402T power supply cable (B)

Dedicated cables are included. Refer to Figure 2.14 and Figure 2.16 for wiring. The lengths of 

the terminal processes at both ends are different. Connect the longer side (approx. 80 mm) to 

TB830D side and the shorter side (approx. 50 mm) to FLXA402T side. Cables have no terminal 

names on them. Wire them by color. L:Black, N: White, G: Red. The tightening torque of M3 

screws (L and N) is 0.6 N·m, and that for M4 screws (G) is 1.4 N·m.

n

  TB830D power supply cable (C)

power supply cabling that connects the Relay box to TB830D.
Dedicated cables are included. Refer to Figure 2.14, 

Figure 2.15

, and Figure 2.16 for wiring. 

Cables have no terminal names on them. Wire them by color. L:Black, N: White, G: Red. M3 The 

tightening torque for screws (L and N) is 0.6 N·m, and that for M4 screws (G) is 1.4 N·m .

n

  Relay Box power supply cable (D)

This is a power supply cable that connects a Relay box to another Relay box when a Relay box is 

attached.
Dedicated cables are included. Refer to Figure 2.14 and Figure 2.16 for wiring. Cables have 

no terminal names on them. Wire them by color. L:Black, N: White, G: Red. M3 The tightening 

torque for screws (L and N) is 0.6 N·m, and that for M4 screws (G) is 1.4 N·m .

Содержание TB830D






















































































Отзывы:

Нет отзывов