YOKOGAWA FA-M3V e-RT3 Plus Скачать руководство пользователя страница 170

Страница: 170 / 274

A3-10

IM 34M06C11-01E

A3.2.5

Mounting Depth and Space

- The depth of the installed module and the base module together is approximately

90mm. An additional length should be allowed for cable bending however, if any

cable with connectors is attached to the controller.

Terminal block type

80 min.

—

Connector type

83.2

Module

D (mm)

d (mm)

FA030212.VSD

Figure A3.6 Mounting Depth

- In the case of fiber-optic FA-bus, fiber-optic FA-bus type 2 and fiber-optic FA link H

modules, the mounting depth should allow for the bending radius of their fiber-optic

cords or cables.

Fiber-optic cord

15 min.
50 min.

50 min.

Fiber-optic cable

100 min.

During cable laying

(Temporary)

Bending Radius r (mm)

When secured

FA030213.VSD

Figure A3.7 Mounting Depth for Modules with Fiber-optic Cords or Cables

When you lay the fiber-optic cord or cable yourself, follow the instructions given below.
1. The product comes with an instruction manual. The person in charge of wiring

should first read the manual thoroughly, and then lay the cord or cable as instructed.

2. Upon delivery, be sure to test the performance of the product by sending light beams

through it. The performance of optical fiber can be easily tested by sending sunlight

or flashlight beams from one end of the cord or cable and confirming their arrival at

the other end.

Test the performance of the product before installation.

Note

Before laying cables, customers should check the cables (immediately after

delivery) for any defect.

In principle,

the provided warranty does not cover functional

defects (e.g., cable discontinuity) discovered after installation.

Fiber-optic cables KM61, KM62, KM65, KM67, and KM69 are made-to-order

products. Hence, replacement of a defective cable may require a week for KM65

cables, a month for KM61, KM62, and KM67 cables, and two months for KM69

cables.

Содержание FA-M3V e-RT3 Plus



















































































































































































































































































Результаты поиска

Содержание FA-M3V e-RT3 Plus

Отзывы:

Похожие инструкции для FA-M3V e-RT3 Plus

Бренды по названию

Популярные бренды

YOKOGAWA FA-M3V e-RT3 Plus, Руководство по оборудованию

Результаты поиска

Содержание FA-M3V e-RT3 Plus

Отзывы:

Похожие инструкции для FA-M3V e-RT3 Plus

Бренды по названию

Популярные бренды