YOKOGAWA EJA210E Скачать руководство пользователя страница 6

  

<1.  Introduction>

1-2

IM 01C25C01-01E

 Regarding This Manual

•  This manual and the identification tag attached 

on the packing box are essential parts of the 

product. Please keep them in a safe place for 

future reference. 

•  This manual should be provided to the end 

user.

•  The contents of this manual are subject to 

change without prior notice.

•  All rights reserved. No part of this manual may 

be reproduced in any form without Yokogawa’s 

written permission.

•  Yokogawa makes no warranty of any kind with 

regard to this manual, including, but not limited 

to, implied warranty of merchantability and 

fitness for a particular purpose.

•  If any question arises or errors are found, or if 

any information is missing from this manual, 

please inform the nearest Yokogawa sales 

office.

•  The specifications covered by this manual are 

limited to those for the standard type under the 

specified model number break-down and do not 

cover custom-made instruments.

•  Please note that changes in the specifications, 

construction, or component parts of the 

instrument may not immediately be reflected 

in this manual at the time of change, provided 

that postponement of revisions will not cause 

difficulty to the user from a functional or 

performance standpoint.

•  Yokogawa assumes no responsibility for this 

product except as stated in the warranty.

•  If the customer or any third party is harmed by 

the use of this product, Yokogawa assumes 

no responsibility for any such harm owing to 

any defects in the product which were not 

predictable, or for any indirect damages. 

•  The following safety symbols are used in this 

manual:

WARNING

 

Indicates a potentially hazardous situation which, 

if not avoided, could result in death or serious 

injury.

CAUTION

Indicates a potentially hazardous situation which, 

if not avoided, may result in minor or moderate 

injury. It may also be used to alert against unsafe 

practices.

IMPORTANT

Indicates that operating the hardware or software 

in this manner may damage it or lead to system 

failure.

NOTE

Draws attention to information essential for 

understanding the operation and features.

 Direct current

 Functional grounding terminal

 Caution

This symbol indicates that the operator must 

refer to an explanation in the user’s manual 

in order to avoid the risk of injury or death of 

personnel or damage to the instrument.

 Trademarks 

•  ‘DPharp’, ‘EJX’, ‘EJA’, ‘FieldMate’ and ‘BRAIN 

TERMINAL’ are registered trademarks or 

trademarks of Yokogawa Electric Corporation. 

Company names and product names used 

in this material are registered trademarks or 

trademarks of their respective owners. 

•  In this manual, trademarks or registered 

trademarks are not marked with ™ or ®.

Содержание EJA210E






























































Отзывы: