YOKOGAWA 701715 Скачать руководство пользователя страница 66

Страница: 66 / 454

3-6

IM 701730-01E

Turning the Main Power Switch ON and OFF

The main power switch is located in the right center of the rear panel. Press the switch

on the ON side to turn the power ON, and on the OFF side to turn the power OFF.

PER

IPHE

RAL

USB

ISM

1-A

N200

MAIN

100-1

20V

/220

-240

V A

250V

A M

50/6

0Hz

FUS

250V

T 4

EXT

CLO

CK IN

EXT

TRIG

ATE

0Vpk

GO/
NO-G

PRO

BE P

OUT

)

OFF

LINK

ACT

MAIN POWER

OFF

Turning the Power Switch ON and OFF

Items to Be Checked before Turning ON the Power

• That the instrument is properly installed:

3.2 Installing the Instrument

• That the power cord is properly connected:

Connecting the Power Cord (page 3-5)

Turning the Power Switch ON and OFF

The power switch is located in the lower left corner of the front panel. The power switch

is a push button. Press once to turn it “ON” and press again to turn it “OFF.”

OFF

Power Up Operation

Self-test and calibration start automatically when the power switch is turned ON. If the

check results are satisfactory, the normal waveform display screen will appear.

Note

•

Allow at least ten seconds after turning OFF the main power switch and the power switch

before turning it ON again.

•

If self-test and calibration do not start when the power is turned ON, or if the normal waveform

display screen does not appear, turn OFF the main power switch and the power switch and

check the following points.

•

That the power cord is plugged in properly.

•

That the correct voltage is coming to the power outlet (see page 3-5).

•

That the power fuse has not blown -> See section 16.5.

If the instrument still fails to power up when the main power switch and the power switch is

turned ON after checking these points, contact your nearest YOKOGAWA dealer.

3.3 Connecting the Power Supply and Turning the Power Switch ON and OFF

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды