Yoder Smokers YS 640, Руководство по эксплуатации

Страница: 22 / 30

21
10. Turn the power switch “on.” This starts the combustion air fan and illuminates the power light. Press
the “start” button on the control panel to activate the auger feed system. (The default temperature set
point is 350° F). If a higher or lower temperature setting is desired, use the increase/decrease buttons
to set the temperature. This can be adjusted at any time after the start cycle is activated. (For cool/cold
season or high temperature cooking see the Selectable Heat Up Modes [Page 11]).
Once the start cycle is activated, three lines will appear on the display panel from lower left to upper right
indicating “heat up” mode. Once the grate temperature reaches
110° F, the actual grate temperature is displayed, alternating with the mode lines.
If the grate temperature range is exceeded during the “heat up” mode, dashing lines will appear from
upper left to lower right indicating “cool down” mode. Once the target temperature range is attained, the
lines will fl ash horizontal indicating “maintenance mode”. The controller will display grate temperatures
when the set point is between 150 and 495° F When the set point is between 500 and 600° F, the display
will show the set point and not the actual grate temperature.
11. Flames should be visible on the burn grate within 3 to 4 minutes. (The igniter is active for 2 minutes.
When you hit “start”, the auger turns continuously for 45 seconds to prime the burn grate. At 46
seconds, the igniter is powered on; within 2 minutes, the heat from the igniter and the combustion air
from the fans will have a small smoldering
fi re started.
NOTE: The only way to reactivate the igniter is to turn the cooker o ff and let it go through the cool down
cycle, or simply pull the plug for a hard reset at which point you can restart the cooker. Before restarting
the Yoder, remove the grates and heat di ff user and inspect the burn grate for any pellet over fl ow. Remove
all pellets from the burn grate area and from the pit fl oor if present.
12. Once the temperature reaches the set point, open the cooking chamber and carefully oil the grates
with vegetable oil. You are ready to cook!
Shutting Down The Smoker
When fi nished cooking, push the power switch to the “o ff ” position. The controller will begin its automatic
shutdown procedure.
•
The auger feed system will stop feeding fuel.
•
The combustion cooling fan will continue to run until the fi re is burned clean.
•
The fan will continue to run until the grill temperature reaches 125° F or 18 minutes, whichever
occurs fi rst.
•
When the procedure is complete, the fan and power LED will turn o ff .
•
Disconnect the Yoder from its power source. When the grill is completely cool, cover the grill to
protect your investment and keep the pellets dry.
38
640 IGNITER AND THERMOCOUPLE COMPONENTS
ITEM # PART # DESCRIPTION QTY.
1 W90777 YS, PELLET, 640 SMOKE CHAMBER, WELDMENT 1
2 1420WHN NUT, WHIZ, 1/4-20 1
3 10X34HHSDS SCREW, HEX HEAD, SELF DRILLING, 10 X 3/4 6
4 1420X1HB BOLT, HEX, 1/4-20 X 1” LONG 1
5 91713 YS, WELDMENT, AUGER COVER BRKT, PELLET 1
6 W90812 YS, WELDMENT, FIREPOT MOUNT, PELLET 1
7 W91078 YS, WELDMENT, BURN POT, PELLET SMOKER 1
8 A90423 YS, IGNITER ASSEMBLY, PELLET SMOKER 1
9 A91413 YS, ASSEMBLY, THERMOCOUPLE, PELLET SMOKER 1