ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
11
12
NOTE
:
CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE
MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT
WOULD CAUSE EXCESS VIBRATION, MOVEMENT OF A FEW CENTIMETERS IS QUITE ACCEPTABLE
AND DOES NOT SUGGEST ANY PROBLEMS
TO REDUCE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURE THE MOUNTING
BRACKET AND DOWNROD ARE SECURE
BALANCING A WOBBLING CEILING FAN
For your convenience, a balancing kit is included: please follow this procedure when balancing the
fan:
1.Check that all blades and blade arm screws are secure.
2.Most fan wobbling problems result from blade levels are unequal. Check this level by selecting a
point on the ceiling above one fan blade’s tip. Measure this distance. Rotate the fan until the next
blade is positioned for measurement. Repeat for each blade. The distance deviation should be equal
within 1/8" (0.32cm).
3.Use the enclosed blade balancing kit if the blade wobbling is still noticeable.
4.If the blade wobble is still noticeable, interchanging two adjacent
(side by side) blades can redistribute the weight and possibly result
in smooth operation.
WARNING
: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARM WHILE
INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT OBJECTS BETWEEN
ROTATING FAN BLADES
NOISE
It’s normal to hear small occasional noises when in quiet night or days. Please allow a 24-hour
"breaking-in" period, most noises of a new fan disappear during the time.
HOW TO USE BALANCING KITS
1.Periodically cleaning your ceiling fan is the only required maintenance. Use a
soft brush or lint free cloth to avoid scratching the paint. Please turn off the
electricity power before you clean your fan.
2.Do not use water when cleaning your ceiling fan. It could damage the motor or
the blades or even evoke an electrical shock.
3.The motor has permanently lubricated ball bearing. No need to oil
NOTE
: MAKE SURE THE POWER IS OFF IN THE ELECTRICAL PANEL BOX BEFORE
YOU DO ANY CLEANING OR REPAIRS
MAINTENANCE AND CLEANING
!
Within the 30s after turning "ON" the power supply, press the “FAN ON/OFF" buttons of
transmitters for 5s. Then the pairing is successfully activated and all functions will work
normally.
IMPORTANT:PAIRING BETWEEN REMOTE AND RECEIVER
The first step of pairing must be performed within 30s after turning on the power supply.
1.(a)When pairing multiple fans, please ensure the isolation switch or the power supply to
the first installed fan is turned off prior to pairing further fans. Please pair one fan at a
time. (b)Please ensure the isolation switch is kept "ON". The isolation switch can not act
as a light switch as this will impair the remote receiver.
2.When the transmitter’s functions are disabled, please check the battery orientation and
power level. Low battery voltage will affect your transmitter's functions and your fan's
operation.Other remote controls nearby using the same frequency may interfere with
your fan's receiver.
3.Please remove batteries from the transmitter if not used for a long period of time.
4.Remote supports 200w maximum lighting.
IMPORTANT NOTES
1.Note: Receiver must be correctly installed on the fan's mounting bracket.
2.When the transmitter cannot control the receiver, please check the battery level.
3.When the transmitter cannot control the receiver, please check if similar remote controls
your fan nearby and interferes with each other.
4.Battery's low power will affect the transmitter's sensitivity and the signal reception
accordingly. You must replace the battery if its power is low.
5.Please take the battery out of the transmitter to avoid battery leaks when not used for a
long time.
6.Isolation switch must be connected in the line.
7.When a blackout or otherwise circumstances happen, the light will work normally after
the power restores.
Please make sure that the fan is powered off before cleaning or maintaining.
IMPORTANT REMINDERS
WARNING
: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARM WHILE
INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT OBJECTS BETWEEN
ROTATING FAN BLADES.
NOISE
: This is normal to hear occasional small noises, when it is quiet (especially at night).
Because slight power fluctuations and frequency signals superimposed in the electricity for
off-peak hot water control may change fan motor noise. Please allow a 24-hour "breaking-in"
period, most noises of a new fan disappear over the time.
!
