YIC Technologies EMProbe Скачать руководство пользователя страница 9

Страница: 9 / 70

www.yictechnologies.com

Software Installation

Plug-in the

EMScanner

USB drive. Select the software folder and double click on

Setup.exe file

2. When you are prompted “Do you want to allow the following program from an

unknown publisher to make changes to this computer” click Yes

3.  Click Next
4.  Click Next
5.  Select I Agree and click Next
6.  Below screen will be displayed
7.  Click Close

If Keysight IO Library is already installed on your PC, you can start using

EMScanner

software. Otherwise please follow the next steps to install it. You need an internet
connection to download Keysight IO Library.

9. Once you are directed to the Keysight website click on the Download button and

follow the steps. When the download is complete, open the Downloads folder and
double click IOLibSuite_xxx.

10. The folder will be unzipped.
11. Click Next
12. Select Agree and click Next
13. Select Typical and click Next
14. Click Install
15. If Microsoft Visual C++ is not installed on your PC below screen will be displayed.

Click Yes

16. While the software is installing, the following screen will be displayed.
17. Click Finish

18.

Connect the USB Cable to the

EMScanner

adaptor and PC

a. The driver will be automatically installed

If the installation doesn’t start automatically, follow below steps. Open the

Device Manager and expand “USB Custom Driver” and right click on

EMScanner

c. Select Browse my computer for driver software

Select Include subfolders and click Browse and select the

EMScanner

USB

drive and click OK

e. Click Next
f. Click Close to complete installation

19.

Start the

EMScanner

Software by clicking the icon on the Desktop

External Spectrum Analyzer Setup

Attention:

An ethernet cross-over cable (static IP must be set for PC and the analyzer) or

USB cable can be used for the PC and spectrum analyzer connection.

USB Connection

If the PC and spectrum analyzer are connected via USB cable skip to Step 2

Содержание EMProbe







































































Результаты поиска

Содержание EMProbe

Отзывы:

Похожие инструкции для EMProbe

Бренды по названию

Популярные бренды

YIC Technologies EMProbe, Руководство пользователя

Результаты поиска

Содержание EMProbe

Отзывы:

Похожие инструкции для EMProbe

Бренды по названию

Популярные бренды