background image

 

 

SAFETY 

 
A brief description of signal words that may be used in this manual: 
 
CAUTION:

 Used as a general reminder of good safety practices or to direct attention to unsafe practices. 

 

WARNING: 

Denotes a specific potential hazard. 

 

DANGER:

 Denotes the most serious specific potential hazard. 

 
 

SAFETY PRECAUTIONS

 

 
You can make your farm a safer place to live and work if you observe the safety precautions given.  Study 
these precautions carefully and insist that those working with you and for you follow them. 
 
Finally, remember this: an accident is 

usually caused by someone’s carelessness, neglect or oversight. 

 

 

WARNING 

 

Never clean, lubricate or adjust a machine that is in motion.  Always lower or block the implement before 
performing service. 
 
If the machine must be serviced in the raised position, jack or block it up to prevent it from accidentally 
falling and injuring someone. 
 
Do not allow riders on the tractor or implement. 
 
Use speeds and caution dictated by the terrain being traversed.  Do not operate on any slope steep enough 
to cause tipping or loss of control. 
 
Be sure all personnel are clear of the immediate area before operating. 
 
Read and understand the operator’s manual and require all other persons who will operate the equipment 
to do the same. 
 
Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in 
an emergency. 
 
 

 

CAUTION 

 

Consult your implement and tractor operator’s manual for correct and safe operating practices. 
 
Beware of towed implement width and allow safe clearance. 
 

 
 

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH. 

 
 
 
 
 
 

Содержание NARROW ROW

















Отзывы: