background image

SB135 

 |

  OWNER’S MANUAL

24

LIFETIME WARRANTY

HERE’S EVERYTHING YOU NEED TO KNOW ABOUT OUR LIFETIME WARRANTY:

All 2019 (or newer) frames, including the Switch Infinity, are covered for life against damage 
due to manufacturing defects for the original purchaser. Paint and finish are covered for 1-year. 
We will repair or replace, at our discretion, any frame we deem defective. There are a few 
conditions: you must register it online at yeticycles.com and you must take it to an authorized 
Yeti Cycles dealer for processing. Warranty does not cover damage due to ordinary wear and 
tear, neglect or intentional destruction. From a slingshot or your truck. 

If you happen to have a crash or non-warranty situation, we’ll get you back on the trail with a 
reasonable replacement price. Same conditions as above. 

Lifetime Warranty applies to all 2019 and newer frames (including the SB100). Model year 
2018 and older frames will be covered under our previous warranty (5-year or 2-year based  
on time of purchase). 

Simple as that. No fine print.

DISCLAIMER

Yeti Cycles is not responsible for any damages to you or others arising from riding, transporting 
or other use of your bicycle. In the event that your frame breaks or malfunctions, Yeti Cycles 
shall have no liability or obligation beyond the repair or replacement of your frame pursuant to 
the terms outlined in the warranty.

*If you have a warranty concern, please contact your authorized Yeti Cycles dealer.

YETI CYCLES

621 Corporate Circle, Unit 
B Golden, CO 80401 
(p) 303-278-6909 
(f) 303-278-6906 

yeticycles.com

BUSINESS HOURS

Monday-Friday  
8AM-11:30AM (MST) 
1:00PM-5:30PM (MST)

Содержание SB135/LR

























Отзывы: