Yeti EP801 Скачать руководство пользователя страница 25

YETI 160E  |  OWNER’S MANUAL

25

ADDITIONAL INFORMATION

TABLE OF CONTENTS  |

ADDITIONAL 

INFORMATION

 

−     To prevent the unauthorized use of you e-bike, secure the bike with a lock or remove  

the battery when not in use.

 

−    Full suspension bikes have many moving parts. Caution should be used to avoid pinch 

points when operating or performing any maintenance on the bike.

 

−    This bike is only intended for one user at a time. Additional users are not permitted  

on this bike.

 

−    Baggy clothing should be avoided while riding this bike as excessively baggy clothing  

can get caught in chain.

 

−   This bike should not be used to tow any cargo or trailers.

 

−    The 160E is not equipped with any lighting equipment needed for nighttime riding.  

We can only recommend daytime operation.

 

−   If riding in traffic, the use of a bell is strongly recommended.

 

−    The 160E is rated to a max system weight of 130Kg and an ASTM 4 rating. Riding in higher 

numbered conditions increases the forces on the bicycle and the risk of injury to the rider.

 

−    The water bottle mounting location is only designed to fit a traditional water bottle cage and 

bottle. Bolting any other item then what is prescribed above could result in frame damage.

 

−    Be advised, use of a mountain bike will result in vibrations that will transmitted to the  

rider. This is inherent to the sport and cannot be avoided.

STORAGE

 

−    Make sure your bike is stored in an area that is free from hazardous conditions that could 

damage the bike or cause an obstruction. Extreme heat or cold should be avoided and 
any machinery that emits ozone or exhaust should not be near your bike when stored.

 

−    Avoid wet conditions that can cause corrosion in certain metal alloys. UV light can 

damage or degrade bicycle components and should avoided during storage.

 

−    Properly service your bike prior to long term storage and when riding the first time after 

storage. See maintenance schedule in this manual for guidance.

TRANSPORT 

Safe transport is critical for protecting the bicycle frame and its components from damage. 
Bikes can be awkward to lift, and proper lifting techniques should be used when loading or 
unloading your bike. Packing your bike should be done by a certified bike mechanic when 
possible. The use of a hard bike case is recommended for the highest level of protection. If the 
wheels are removed for transport, make sure the area where the hub and axle were in the fork 
and rear triangle is sufficiently supported to avoid damage. If transported inside a vehicle, make 
sure all parts of the bike that contact the vehicle are padded properly. When transporting on 
the outside of the vehicle, make sure the bike is not exposed to hot exhaust or debris that can 
impact the bike while moving.

CLEANING

The best way to wash your bike is with a soft brush and rag, using soapy water or a mild cleaner 
such as Motorex Bike Clean or equivalent. Do not use harsh detergents or directly pressure 
wash any of the bearings, hardware or seals. 

BATTERY SAFTEY

 

−    The Shimano battery is waterproof but do not submerse it in water or directly spray any 

electronic components with water − If the battery becomes damaged it must not be 
charged, used, or transported. 

 

−   In case of a battery fire, only use class D fire extinguisher to extinguish the flames. 

 

−  Only charge the battery with certified Shimano STEP’s battery chargers. 

 

−   Only use the approved Shimano battery in the bicycle. 

 

−   See STEPS user manual for further safety information.  

  

https://www.shimanosteps.com/

 

−   Call2Recycle.com has created a program to recycle E bike batteries once they are 

 

 

at the end of their life. For more information, contact your dealer or visit  

  

https://wwwcall2recycle.org/e-bikes/

 to find your closest recycling drop off location. 

WARNING

: Used batteries and electronic equipment may contain harmful substances which, if not properly 

disposed of, could damage the environment and your health. Additionally, batteries and electronics may 
contain important raw minerals, which can be recycled. For this reason, you must not dispose of electrical 
components with household waste, but must return them after use to a specialty store, at a municipal 
collection point or at your nearest authorized Yeti Cycle dealer.

Содержание EP801

































Отзывы: