Yealink W80 Скачать руководство пользователя

Страница: 256 / 260

Appendix

253

Appendix

RFC and Internet Draft Support

The following RFC’s and Internet drafts are supported:

RFC 1321—The MD5 Message-Digest Algorithm

RFC 1889—RTP Media control

RFC 2112—Multipart MIME

RFC 2327—SDP: Session Description Protocol

RFC 2387—The MIME Multipart/Related Content-type

RFC 2543—SIP: Session Initiation Protocol

RFC 2617—Http Authentication: Basic and Digest access authentication

RFC 2782—A DNS RR for specifying the location of services (DNS SRV)

RFC 2806—URLs for Telephone Calls

RFC 2833—RTP Payload for DTMF Digits, Telephony Tones and Telephony Signals

RFC 2915—The Naming Authority Pointer (NAPTR) DNS Resource Record

RFC 2976—The SIP INFO Method

RFC 3087—Control of Service Context using SIP Request-URI

RFC 3261—SIP: Session Initiation Protocol (replacement for RFC 2543)

RFC 3262—Reliability of Provisional Responses in the Session Initiation Protocol (SIP)

RFC 3263—Session Initiation Protocol (SIP): Locating SIP Servers

RFC 3264—An Offer/Answer Model with the Session Description Protocol (SDP)

RFC 3265—Session Initiation Protocol (SIP) - Specific Event Notification

RFC 3310—HTTP Digest Authentication Using Authentication and Key Agreement (AKA)

RFC 3311—The Session Initiation Protocol (SIP) UPDATE Method

RFC 3312—Integration of Resource Management and SIP

RFC 3313—Private SIP Extensions for Media Authorization

RFC 3323—A Privacy Mechanism for the Session Initiation Protocol (SIP)

RFC 3324—Requirements for Network Asserted Identity

RFC 3325—SIP Asserted Identity

RFC 3326—The Reason Header Field for the Session Initiation Protocol (SIP)

RFC 3361—DHCP-for-IPv4 Option for SIP Servers

RFC 3372—SIP for Telephones (SIP-T): Context and Architectures

RFC 3398—ISUP to SIP Mapping

RFC 3420—Internet Media Type message/sipfrag

RFC 3428—Session Initiation Protocol (SIP) Extension for Instant Messaging

RFC 3455—Private Header (P-Header) Extensions to the SIP for the 3GPP

RFC 3486—Compressing the Session Initiation Protocol (SIP)

RFC 3489—STUN - Simple Traversal of User Datagram Protocol (UDP) Through Network Address Translators
(NATs)

RFC 3515—The Session Initiation Protocol (SIP) Refer Method

RFC 3550—RTP: Transport Protocol for Real-Time Applications

RFC 3555—MIME Type Registration of RTP Payload Formats

RFC 3581—An Extension to the SIP for Symmetric Response Routing

RFC 3608—SIP Extension Header Field for Service Route Discovery During Registration

RFC 3611—RTP Control Protocol Extended Reports (RTCP XR)

RFC 3665—Session Initiation Protocol (SIP) Basic Call Flow Examples

Содержание W80





































































































































































































































































Результаты поиска

Содержание W80

Отзывы:

Похожие инструкции для W80

Бренды по названию

Популярные бренды

Yealink W80, Руководство администратора

Результаты поиска

Содержание W80

Отзывы:

Похожие инструкции для W80

Бренды по названию

Популярные бренды