Yealink W80 Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 260

background image

Troubleshooting Solutions

246

Troubleshooting Solutions

This section describes solutions to common issues that may occur while using the device. Upon encountering a
case not listed in this section, contact your Yealink reseller for further support.

Topics

IP Address Issues
Time and Date Issues
Phone Book Issues
Audio Issues
Firmware and Upgrading Issues
System Log Issues
Password Issues
Power and Startup Issues
Other Issues
Base Issue
Handset Issues
Register Issue
Display Issue
Upgrade Issue

IP Address Issues

The device does not get an IP address

Do one of the following:

If your device connects to the wired network:

l

Ensure that the Ethernet cable is plugged into the Internet port on the IP phone and the Ethernet cable is not
loose.

l

Ensure that the Ethernet cable is not damaged.

l

Ensure that the IP address and related network parameters are set correctly.

l

Ensure that your network switch or hub is operational.

Time and Date Issues

Display time and date incorrectly

Check if the IP phone is configured to obtain the time and date from the NTP server automatically. If your phone is
unable to access the NTP server, configure the time and date manually.

Phone Book Issues

Difference between a remote phone book and a local phone book

A remote phone book is placed on a server, while a local phone book is placed on the IP phone flash. A remote
phone book can be used by everyone that can access the server, while a local phone book can only be used on a
specific phone. A remote phone book is always used as a central phone book for a company; each employee can
load it to obtain real-time data from the same server.

«
...
247
248
249
250
251
...
»

Содержание W80





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для W80

-295861 - Corded Desktop CID Itad

Бренд: GE Страницы: 44

Бренд: Dakota Alert Страницы: 2

Бренд: Daisy Страницы: 16

Бренд: DAINCUBE Страницы: 38

Бренд: BT Страницы: 25

Бренд: Commax Страницы: 16

Бренд: Topcom Страницы: 20

Бренд: Jabra Страницы: 8

D7000 Vita Plus

Бренд: switel Страницы: 98

Бренд: GE Страницы: 60

Бренд: Home Decorators Collection Страницы: 24

Бренд: AEG Страницы: 176

Бренд: AEG Страницы: 48

Voxtel D555 twin

Бренд: AEG Страницы: 120

Бренд: AEG Страницы: 124

Бренд: AEG Страницы: 198

Бренд: AEG Страницы: 280

Бренд: Motorola Страницы: 131

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды