Yazoo/Kees 968999663 Скачать руководство пользователя страница 49

Страница: 49 / 84

English-

MAINTENANCE

Blade replacement

•

Remove blade bolt by turning
counterclockwise.

•

Install new or re-sharpened blade with
stamped "GRASS SIDE" facing towards
ground/grass (down) or “THIS SIDE UP”
facing deck and cutter housing.

•

Install and tighten blade bolt securely.
Torque blade bolt to 90 ft/lbs (122 Nm).

WARNING!

Blades are sharp. Protect your

hands with gloves and/or wrap
blades with a heavy cloth when

handling.

IMPORTANT INFORMATION
To ensure proper assembly, center hole in
blade must align with star on cutter
housing.

IMPORTANT INFORMATION
Special blade bolt is heat treated.
Replace with a Yazoo/Kees bolt if required.
Do not use lower grade hardware than
specified.

1. Blade

2. Center hole

3. Cutter housing

4. Blade bolt

5. Lockwasher

Blade attachment

Содержание 968999663





















































































Результаты поиска

Содержание 968999663

Отзывы:

Бренды по названию

Популярные бренды

Yazoo/Kees 968999663, Руководство оператора

Результаты поиска

Содержание 968999663

Отзывы:

Бренды по названию

Популярные бренды