manualshive.com logo in svg

Yazoo/Kees 968999663, Руководство оператора

Поделиться
Скачать
Yazoo/Kees 968999663 Скачать руководство пользователя страница 32

English-

30

OPERATION

Running

1. Release the parking brake by moving the 

lever forward.
Your mower is equipped with an operator 
presence system. When the engine is 
running, any attempt by the operator to 
leave the seat without first setting the 
park brake will shut off the engine.

2. Move the steering controls to the neutral 

position (N).

3. Select the cutting height by placing the 

peg in one of the holes. Lock the peg on 
the inside with the pin.

4. Press in the stop handle, counter hold, 

and carefully move the lifting lever 
forward from the transport position 
toward the peg.

5. Engage the mower deck by pulling out 

the blade switch.

6. Move the throttle control to full throttle.
7. The machine’s speed and direction are 

continuously variable using the two 
steering controls. When both controls are 
in the neutral position, the machine 
stands still. 
By moving both controls an equal 
amount forward or backward, the 
machine moves in a straight line forward 
or backward respectively. 

8011-511

Released parking brake

8011-561

Cutting height selection

IMPORTANT INFORMATION
The mower deck’s anti-scalp rollers should 
be evenly adjusted.

WARNING!
Ensure that no one is near the 
machine when engaging the 
Blade switch.

8011-510

Engaging the mower deck

Содержание 968999663





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды