Yazoo/Kees 968999660 Скачать руководство пользователя страница 30

English

-

30

OPERATION

Before Starting

Read the sections on Safety Instructions and 

• 

Controls before starting the machine.
Perform the daily maintenance before starting 

• 

(see Maintenance section).

Check that there is sufficient fuel in the fuel 

• 

tank.
Adjust the seat to the desired position.

• 
The following conditions must be fulfilled before the 

engine can be started:

The driver must be seated on the seat.

• 

The blade switch for engaging the mower 

• 

blades must be depressed.
The parking brake must be on.

• 

Both steering controls must be in the locked 

• 

(outer) neutral position.

Starting the Engine

Sit on the seat. 

• 

Raise the mower deck by pulling the lifting 

• 

lever backward to the locked position (transport 

position).
Activate the parking brake.

• 

8011-525-02

Raise the mower deck to transport position

8011-640-1

Conditions for starting

8011-508 

Depress blade switch control the disengage deck

Disengage the mower blades by depressing 

• 

the blade switch.

Содержание 968999660





































































Отзывы: