manualshive.com logo in svg

YASKAWA VS MINI J7 series, Инструкция по эксплуатации

Поделиться
Скачать
YASKAWA VS MINI J7 series Скачать руководство пользователя страница 91

91

• Preventing Motor from Stalling (Current Limit)

This function automatically limits the output current in response to load changes by 
adjusting the output frequency to prevent motor stalling.

•

Stall prevention (current limit) level during acceleration (n56)

Sets the stall prevention (current limit) level during acceleration in units of 1% 
(Inverter rated current = 100%).

Factory setting: 170%

A setting of 200% disables the stall prevention (current limit) during acceleration. 
During acceleration, if the output current exceeds the value set for n56, acceleration 
stops and frequency is maintained. When the output current goes down to the value set 
for n56, acceleration continues.

In the constant horsepower area [output frequency > max. voltage output frequency 
(n11)], following equation automatically decreases the stall prevention (current limit) 
level during acceleration.

* Stops the acceleration to prevent the motor 

from stalling.

† Release width (hysteresis) of stall prevention 

during accel is approx. 5% of inverter rated 
current.

*

*

*Note: The lower limit of the stall prevention level is 40% of the level set in n56.

All manuals and user guides at all-guides.com

all-guides.com

Содержание VS MINI J7 series























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды