5.8 L: Protection Functions
YASKAWA ELECTRIC
SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual
185
P
a
ra
me
te
r D
eta
ils
5
5.8 L: Protection Functions
◆
L1: Motor Protection Functions
■
L1-01: Motor Overload Protection Selection
The drive has an electronic overload protection function that estimates the motor overload level based on output current,
output frequency, thermal motor characteristics, and time. An oL1 fault will be triggered when motor overload is
detected.
L1-01 sets the overload protection function characteristics according to the motor being used.
Note: 1.
When the motor protection function is enabled (L1-01 is not set to zero), an oL1 alarm can be output through one of the multi-
function outputs by setting H2-01 to 1F. The output will close when the motor overload level reaches 90% of the oL1 detection level.
2.
Select a method to protect the motor from overheat by setting L1-01 between 1 and 4 when running a single motor from the drive. An
external thermal relay is not needed.
Setting 0: Disabled - Motor Overload Protection is not Provided
This setting should be used if no motor overheat protection is desired or if multiple motors are connected to one drive. In
this case it is recommended that you install a thermal relay for each motor as show in
Figure 5.64
Figure 5.64 Example of Protection Circuit Design for Multiple Motors
NOTICE:
Protect each motor with individual thermal overloads when multiple motors are connected to one drive. Failure to comply
could result in motor damage. Disable the electronic overload protection of the drive (L1-01 = “0: Disabled”) and protect each motor
with individual motor thermal overloads.
Setting 1: General Purpose Motor (standard self-cooled)
Because the motor is self-cooled, the overload tolerance drops when the motor speed is lowered. The drive appropriately
adjusts the electrothermal trigger point according to the motor overload characteristics, protecting the motor from
overheat throughout the entire speed range.
No.
<1> Default setting depends on the control mode selection in parameter A1-02. The value shown here is for V/f Control.
Dependent Parameter Default Values on page 364
.
Name
Setting Range
Default
L1-01
Motor Overload Protection Selection
0 to 4
1
Overload Tolerance
Cooling Capability
Overload Characteristics
at 100% Motor Load
Motor designed to operate from line
power.
Motor cooling is most effective when
running at rated nameplate base
frequency (check the motor
specifications).
Continuous operation at less than line
power frequency with 100% load can
trigger motor overload protection (oL1).
A fault is output and the motor will coast
to stop.
Drive
Power
supply
M1
MC1
MC1, MC2: Magnetic contactors
L10, L20: Thermal relays
L10
MC2
L20
M2
A: Max. speed for 200LJ and above
B: Max. speed for 160MJ to 180 LJ
C: Max. speed for 132MJ and below
Содержание T1000V
