manualshive.com logo in svg

YASKAWA SI-EL3/V, Руководство по установке, Страница: 6 / 34

Поделиться
Скачать
YASKAWA SI-EL3/V Скачать руководство пользователя страница 6

1  Preface and Safety

EN 6 

YASKAWA Europe 

YEU TOEP C710606 87A - V1000 Option Powerlink - Installation Manual

Supplemental Safety Information

Read and understand this manual before installing, operating, or servicing this option card.
The option card must be installed according to this manual and local codes.
The following conventions are used to indicate safety messages in this manual. Failure to
heed these messages could result in serious or possibly even fatal injury or damage to the
products or to related equipment and systems.

General Safety

DANGER 

Indicates a hazardous situation, which, if not avoided, will result in death or serious injury

.

W ARNING 

Indicates a hazardous situation, which, if not avoided, could result in death or serious

injury.

CAUTION 

Indicates a hazardous situation, which, if not avoided, could result in minor or moderate

injury.

NOTICE

Indicates an equipment damage message.

General Precautions

• The diagrams in this section may include drives without covers or safety shields to illustrate details. Be sure to rein-

stall covers or shields before operating any devices. The option board should be used according to the instructions 
described in this manual.

• Any illustrations, photographs, or examples used in this manual are provided as examples only and may not apply 

to all products to which this manual is applicable.

• The products and specifications described in this manual or the content and presentation of the manual may be 

changed without notice to improve the product and/or the manual.

• When ordering a new copy of the manual due to damage or loss, contact your YASKAWA representative or the 

nearest YASKAWA sales office and provide the manual number shown on the front cover.

Содержание SI-EL3/V



































Отзывы:

Нет отзывов