YASKAWA CIMR-R5U20111A Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 69

YASKAWA CIMR-R5U20111A Скачать руководство пользователя страница 7

i.2 Safety Information

YASKAWA ELECTRIC

TOEP C710656 01C YASKAWA - RC5 Instruction Manual

5

i.2

Safety Information

Read this instruction manual thoroughly before installation, operation, maintenance or inspection of the RC5. In this manual, NOTES FOR SAFE

OPERATION are classified as “WARNING” or “CAUTION.”

◆

Supplemental Safety Information

WARNING!

will also be indicated by a bold key word embedded in the text followed by an italicized safety message.

CAUTION!

will also be indicated by a bold key word embedded in the text followed by an italicized safety message.

NOTICE:

will also be indicated by a bold key word embedded in the text followed by an italicized safety message.

Even items described in a Caution may result in a vital accident in some situations. In either case, follow these important notes.

Note:

These are steps to be taken to insure proper operation.

General Precautions

• Some drawings in this manual are shown with the protective cover or shields removed, in order to describe detail with more clarity. Make sure all covers and shields

are replaced before operating this product.

• This manual may be modified when necessary because of improvement of the product, modification, or changes in specifications.
• Such modifications are denoted by a revised manual No.
• To order a copy of this manual, if your copy has been damaged or lost, contact your YASKAWA representative.
• YASKAWA is not responsible for any modification of the product made by the user, since that will void your guarantee.

W ARNING

Read and understand this manual before installing, operating or servicing this drive. The drive must be installed according to this manual and local
codes.
The following conventions are used to indicate safety messages in this manual. Failure to heed these messages could result in serious or possibly
even fatal injury or damage to the products or to related equipment and systems.

DANGER

Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.

W ARNING

Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.

NOTICE

Indicates a property damage message.

«
...
5
6
7
8
9
...
»

Содержание CIMR-R5U20111A






































































Отзывы:

Нет отзывов