Yardworks SN70016-1 Скачать руководство пользователя страница 9

Clear snow often, before it gets too deep. It is best to  

remove the snow as soon as possible after it falls. 

Lift the auger up slightly before starting the snow thrower. 

Switch on and tilt the snow thrower forward until the 

scraper blade contacts the ground.  Push the snow 

thrower forward at a comfortable rate of speed, yet slow 

enough to clear the path completely. The width and depth 

of the snow determines your forward speed. 

Pull up and turn the adjust knob to direct the snow to the 

right or to the left. For the most efficient snow removal 

throw the snow downwind and slightly overlap each 

swath. 

The snow thrower can remove up to 8” deep in one pass.  

When clearing deeper drifts, hold the snow thrower by 

the upper and lower handles and use a swinging or 

sweeping motion.  Shave off the top layer and make   

multiple passes. (Fig. 6). 

OPERATING 

Model SN70016-1 SKU 270-3286

This snow thrower is intended to be used to sweep snow 

from sidewalks, steps, patios, decks and other hard flat 

surfaces such as paved driveways.  Use it only on hard, 

flat surfaces free of sand, stone and debris, wires or any 

other objects.  The manufacturer is not liable for any 

damage or injury resulting from misuse. 

On/Off Switch 

(Fig. 4) 

WARNING:

 The auger starts rotating  

immediately after the snow thrower is switched on. 

Keep hands and feet away from the auger.  

To switch ON, hold the snow thrower firmly with two 

hands, make sure the auger is not touching any surface 

and press the Safety Lock Off Button (2) while squeezing 

the On/Off trigger switch (3).  

Once the snow thrower is started you can release the 

Safety Lock Off Button. 

To switch Off simply release the trigger. 

Removing snow

WARNING:

 Before starting work, make sure that 

the area to be cleared is free of stones, debris, 

wires and any other  objects.  

Make sure all fasteners on the snow thrower (screws, 

nuts, etc.) are fully tightened. 

Check the auger for wear and tear at regular intervals. 

Position the snow thrower so that snow will discharge in 

a safe direction away from the operator and bystanders. 

Correct 

Incorrect 

8”

 

Содержание SN70016-1















Отзывы: