Yardworks 054-5745-0 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 40

Yardworks 054-5745-0 Скачать руководство пользователя страница 12

model no. 054-5745-0 | contact us: 1.866.523.5218

12

Electrical Inf

ormation

Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.

A proper extension cord is available at an authorized service centre.

It is possible to tie the extension cord and power cord in a knot to prevent them from becoming

disconnected during use. Make the knot as shown in Fig. 4, then connect the plug end of the

power cord into the receptacle end of the extension cord. This method can also be used to tie

two extension cords together.

Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s)

to be used for the gardening appliance. Receptacles are available having built-in GFCI protection

and may be used for this measure of safety.

!

WARNING: Check extension cords before each use. If

damaged replace immediately. Never use the product with

a damaged cord since touching the damaged area could

cause electrical shock resulting in serious injury.

!

WARNING: Keep the extension cord clear of the working

area. Position the cord so that it will not get caught on

lumber, tools, or other obstructions while you are working

with a power tool. Failure to do so can result in serious

personal injury.

«
...
10
11
12
13
14
...
»

Содержание 054-5745-0









































Отзывы:

Нет отзывов