background image

STORAGE

At the end of the season (or if the plate compactor will not be used 
for 30 days or longer), follow the storage instructions below.

1.     Run the engine until the fuel lines and carburetor are empty 

and it stops due to lack of fuel.

2.     Allow the engine to cool.

3.     lubricate the machine as instructed.

4.     Clean  the  exterior  of  the  engine  and  the  plate  compactor 

thoroughly.

5.     Touch up all rusted or chipped paint surfaces; sand affected 

areas before painting, and use a rust preventative to prevent 
the metal parts from rusting.

6.     Tighten all loose screws, bolts, and locknuts. Repair or replace 

any damaged parts.

7.     Cover the machine and store it in a clean, dry place out of the 

reach of children.

PRECAUTIONS

1.     Drain the fuel tank completely. Stored fuel containing ethanol 

or MTbE can start to go stale in 30 days. Stale fuel has high 
gum content and can clog the carburetor and restrict fuel flow.

2.     Start the engine and allow it to run until it stops. This ensures 

no fuel is left in the carburetor, and helps prevent deposits 
from forming inside the carburetor, which can damage the 
engine.

3.     While the engine is still warm, drain the oil from the engine. 

Refill with fresh oil of the grade recommended in the Engine 
Manual.

4.     Allow the engine to cool. Remove the spark plug and put 60 

ml of SAE-30 of high quality motor oil into the cylinder. Pull 
the starter rope slowly to distribute the oil. Replace the spark 
plug.

5.     Use clean cloths to clean off the outside of the compactor and 

to keep the air vents free of obstructions.

6.     Pull up the spring bolt and fold up the wheels bracket. (See 

Figure 4b, 

Page 9)

7.     Carefully fold the upper handle down. Do not allow control 

cables to become pinched or bent. (See 

Figure 10

)

Refer to the Engine Manual for information on 
storing your engine.

Remove the spark plug and drain all of the oil from 
the cylinder before attempting to start the unit after 
storage.

Do not use strong detergents or petroleum based 
cleaners when cleaning plastic parts. Chemicals can 
damage plastics.

Figure 10

17

|

   Service & Storage

29140US25M100.indd   17

2017/3/20   13:50:29

Содержание YC0850

























Отзывы:

Похожие инструкции для YC0850