YARDMAX YB6870 Скачать руководство пользователя страница 7

ENGINE SAFETY

This machine is equipped with an internal combustion engine. 
Do not use on or near any unimproved, forest covered, or brush 
covered land unless the exhaust system is equipped with a spark 
arrester meeting applicable local, state, or federal laws.

In the state of California, a spark arrester is required by law. 
Other states have similar laws. A spark arrester, if used, must be 
maintained in effective working order by the operator.

never start or run the engine inside a closed area. The exhaust 
fumes are dangerous, containing carbon monoxide, an odorless 
and deadly gas. Operate this unit only in a well-ventilated 
outdoor area.

Do not tamper with the engine to run it at excessive speeds. The 
maximum engine speed is preset by the manufacturer and is 
within safety limits. See engine manual.

Keep a Class b fire extinguisher on hand when operating this 
snow blower in dry areas as a precautionary measure.

FUEL SAFETY

Fuel is highly flammable, and its vapors can explode if ignited. 
Take precautions when using to reduce the chance of serious 
personal injury.

When refilling or draining the fuel tank, use an approved fuel 
storage container while in a clean, well-ventilated outdoor area. 
Do not smoke, or allow sparks, open flames, or other sources of 
ignition near the area while adding fuel or operating the unit. 
Never fill the fuel tank indoors.

Keep grounded conductive objects, such as tools, away from 
exposed, live electrical parts and connections to avoid sparking or 
arcing. These events could ignite fumes or vapors. 

Always stop the engine and allow it to cool before filling the fuel 
tank. never remove the cap of the fuel tank or add fuel while the 
engine is running or when the engine is hot. Do not operate the 
machine with known leaks in the fuel system.

Loosen the fuel tank cap slowly to relieve any pressure in the tank. 

never overfill the fuel tank. Fill the tank to no more than 1/2” 
below the bottom of the filler neck to provide space for expansion 
as the heat of the engine can cause fuel to expand.

Replace all fuel tank and container caps securely and wipe up spilled 
fuel. never operate the unit without the fuel cap securely in place.

Avoid creating a source of ignition for spilled fuel. If fuel is spilled, 
do not attempt to start the engine but move the machine away 
from the area of spillage and avoid creating any source of ignition 
until fuel vapors have dissipated.

When fuel is spilled on yourself or your clothes, wash your skin 
and change clothes immediately.

Store fuel in containers specifically designed and approved for 
this purpose.

Store fuel in a cool, well-ventilated area, safely away from sparks, 
open flames, or other sources of ignition.

never store fuel or a machine with fuel in the tank inside a 
building where fumes may reach a spark, open flame, or any other 
source of ignition, such as a water heater, furnace, or clothes 
dryer. Allow the engine to cool before storing in any enclosure.

Do not operate without wearing adequate winter outer garments.

Do not use the machine on a roof. 

Do not run the engine indoors, except when starting the engine 
and for transporting the snow thrower in or out of the building. 
Open the outside doors; exhaust fumes are dangerous.

Always check overhead and side clearances carefully before 
operation. Always be aware of traffic when operating along 
streets or curbs.

Thoroughly inspect the area to be worked. Keep the working area 
clean and free of toys, doormats, newspapers, sleds, boards, wires 
and other foreign objects, which could be tripped over or thrown 

by the auger/impeller. Check for weak spots on docks, ramps or 
floors.

Plan your snow-throwing pattern to avoid discharge toward 
people or areas where property damage can occur.

Do not operate near drop-offs, ditches, or embankments. 
Machine can suddenly turn over if a wheel is over the edge of a 
cliff or ditch, or if an edge caves in.

Keep all bystanders, children, and pets at least 75 feet (23m) 
away. If you are approached, stop the unit immediately.

Use a grounded three-wire extension cord and receptacle for all 
machines with electric start engines.

SPECIFIC SAFETY RULES

6

Two-Stage Snow blower   

»   

Operator’s Manual

 

     

YB6870PM00 - 1807

Safety    

|

Содержание YB6870





































Отзывы: