YARDMAX YB6270 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 32

YARDMAX YB6270 Скачать руководство пользователя страница 16

AUGER CLUTCH AND DRIVE CLUTCH

When auger clutch lever or drive clutch lever is
released and in the disengaged position, the cable
should have very little slack.

Auger must stop within 5 seconds when the auger clutch
lever is released. If auger clutch does not engage or
disengage properly, adjust auger clutch before operation.

If the snow blower’s drive is disengaging intermittently
during operation, or it drives when you release the
drive clutch lever, adjust the drive clutch before
operation.

both auger clutch and drive clutch can be adjusted at
either end of their control cables.

Figure 10

It is not recommended to operate the snow blower
on gravel as it can easily pick up and throw by the
impeller, causing personal injury or damage to the
snow thrower and surrounding property.

Always adjust skid shoes after adjusting scraper
blade to prevent premature wear to scraper blade or
damage to auger housing.

SKID SHOES

Position the skid shoes based on surface conditions.
For removal of snow in normal conditions, such as
a paved driveway or sidewalk, place skid shoes in
the higher position to give a 1/8” (3mm) clearance
between the scraper blade and the ground. Use a
middle or lower position when the area to be cleared
is uneven.

If you choose to operate the snow thrower on a gravel
surface, use extra caution and keep the skid shoes in
position for maximum clearance between the ground
and the scraper blade.

To adjust the skid shoes:

Loosen the four hex nuts (two on each side) and
carriage bolts. Move skid shoes to desired position.

Make sure the entire bottom surface of skid shoe is against
the ground to avoid uneven wear on the skid shoes.

Retighten nuts and bolts securely.

1.

2.

3.

Figure 9

ADJUSTMEnT

CHUTE BRACKET

If the spiral at the bottom of the directional chute
control lever is not fully engaging with the chute
assembly, the chute bracket must be adjusted.

Loosen lock nut on adjustment turnbuckle.

Turn the adjustment turnbuckle up and down to
increase cable tension or provide more slack.

Retighten lock nut.

1.

2.

3.

15

|

Adjustment

30255JUS25M100.indd 15

2016/9/2 14:49:34

«
...
14
15
16
17
18
...
»

Содержание YB6270

































Отзывы:

Нет отзывов