background image

 2 

[email protected]

Important Safety Notice!

Yardistry components are intended for privacy, decorative and ornamental use only.

Product is NOT INTENDED for the following:

  

•  A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.

 

• As load bearing support for a building, structure, heavy objects or swings.

 

•  Used in structures that trap wind, rain or snow that would create extra load on the 

product.

Accumulated snow must be removed from roof.

DO NOT 

climb or walk on roof for any reason.

Permanent structures may require a building permit. 

 As the purchaser and or installer of this 

product you are advised to consult local planning, zoning and building inspection departments for 

guidance on applicable building codes and/or zoning requirements.

Wood is NOT flame retardant and will burn.

  Grills, fire pits and chimineas are a fire hazard if 

placed too close to a Yardistry structure.  Consult user’s manual of the grill, fire pit or chiminea 

for safe distances from combustible materials.

Wear gloves to avoid injury

 from possible sharp edges of individual elements before assembly.

During installation, follow all safety warnings provided with your tools and use OSHA 

approved  safety glasses

.  Some structures may require two or more people to install safely.

Check for underground utilities before digging or driving stakes into the ground!

During assembly it is important to closely follow the instructions

.  Complete the assembly 

on a solid, level surface and follow the instructions to square up, level and anchor the structure.  

This will reduce the gaps at wood connections during assembly.

General Information:

  Wood components are manufactured with Cedar (C. Lanceolata) 

which is protected with factory applied water-based stain.  Knots, small checks (cracks) 

and weathering are naturally occurring and do not affect the strength of the product.  

Annual application of a water-based water repellent sealant or stain is important and will 

help reduce weathering and checks.

www.yardistrystructures.com

General Information

Questions? 

 Call toll free or write us at:

1 (888) 509-4382

[email protected]

Patents Pending

Regular Hours:  Mon - Fri, 8:30 am - 5:00 pm EST 

(excl. holidays)

(For extended hours see our website)

 English and French Spoken

Содержание YM12952












































































Отзывы: