background image

0

Off-Season 

Storage

Never store snow 
thrower with fuel 
in tank indoors or 
in poorly ventilated 
areas, where fuel 
fumes may reach an 
open flame, spark 
or pilot light as on a 
furnace, water heater, 
clothes dryer or gas 
appliance.

WARNING

Drain fuel into an 
approved container 
outdoors, away from 
any open flame. Be 
certain engine is 
cool. Do not smoke. 
Fuel left in engine 
during warm weather 
deteriorates and will 
cause serious 
starting problems.

Observe the following, when preparing your snow thrower 
for off-season storage:
•  Drain fuel into an approved container outdoors, away 

from any open flame. Allow engine to cool. Extinguish 
cigarettes, cigars, pipes and other sources of ignition 
prior to draining fuel. Fuel left in engine during warm 
weather deteriorates and will cause serious starting 
problems.

•  If unit is to be stored over 30 days, prepare for storage 

as instructed in the separate engine manual packed 
with your unit.

•  Run engine until fuel tank is empty and engine stops 

due to lack of fuel.

•  Remove gasoline from carburetor and fuel tank to 

prevent gum deposits from forming on these parts and 
causing possible malfunction of engine. 

•  Drain carburetor by pressing upward on bowl drain, 

located below the carburetor cover.

•  Fuel stabilizers, such as STA-BIL®, are an acceptable 

alternative in minimizing the formation of fuel gum 
deposits during storage. Do not drain carburetor if 
using a fuel stabilizer.

•  Wipe equipment with an oiled rag to prevent rust.
•  Remove spark plug and pour one ounce of engine oil 

through spark plug hole into cylinder. Cover spark plug 
hole with rag. Crank engine several times to distribute 
oil. Replace spark plug.

•  Follow the lubrication recommendations found in the 

Maintenance Section.

•  Always store the snow thrower in a clean, dry area.

Do not drain 
carburetor if  
using fuel stabilizer. 
Never use engine or 
carburetor cleaning 
products in the fuel 
tank or permanent 
damage may occur.

Содержание 769-03245

























































Отзывы: