Yard-Man 450 Series Скачать руководство пользователя страница 5

5

2

Safe  

Operation 

Practices

WARNING

This symbol points 
out important safety 
instructions which, if 
not followed, could 
endanger the personal 
safety and/or property 
of yourself and others. 
Read and follow all 
instructions in this man-
ual before attempting to 
operate this machine. 
Failure to comply with 
these instructions 
may result in personal 
injury. When you see 
this symbol, 

HEED ITS 

WARNING!

16. Do not overload machine capacity by attempting to till soil to 

deep at too fast of a rate. 

17. If the machine should start making an unusual noise or 

vibration, stop the engine, disconnect the spark plug wire 
and ground it against the engine. Inspect thoroughly for 
damage. Repair any damage before starting and operating.

18. Keep all shields, guards, and safety devices in place and 

operating properly.

19. Never pick up or carry machine while the engine is running.
20. Use only attachments and accessories approved by the 

manufacturer. Failure to do so can result in personal injury.

21. If situations occur which are not covered in this manual, use 

care and good judgment. Contact your dealer or telephone 
1-800-800-7310 for assistance and the name of your 
nearest servicing dealer.

Maintenance & Storage

1.  Never tamper with safety devices. Check their proper 

operation regularly.

2.  Check bolts and screws for proper tightness at frequent 

intervals to keep the machine in safe working condition. 
Also, visually inspect machine for any damage. 

3.  Before cleaning, repairing, or inspecting, stop the engine 

and make certain the tines and all moving parts have 
stopped. Disconnect the spark plug wire and ground it 
against the engine to prevent unintended starting.

4.  Do not change the engine governor settings or over-speed 

the engine. The governor controls the maximum safe 
operating speed of the engine.

5.  Maintain or replace safety and instruction labels, as 

necessary.

6.  Follow this manual for safe loading, unloading, transporting, 

and storage of this machine.

7.  Never store the machine or fuel container inside where 

there is an open flame, spark or pilot light such as a water 
heater, furnace, clothes dryer, etc.

8.  Always refer to the operator’s manual for proper instructions 

on off-season storage.

9.  If the fuel tank has to be drained, do this outdoors.
10. Observe proper disposal laws and regulations for gas, oil, 

etc. to protect the environment.

Your Responsibility 

1.  Restrict the use of this power machine to persons who read, 

understand, and follow the warnings and instructions in this 
manual and on the machine.

2.  The safety labels on the tiller are shown in the “Safety 

Labels” section. To ensure safe operation of the tiller, follow 
the instructions on all labels closely.

Содержание 450 Series





















Отзывы: