background image

25

Model 31BH763G401

Ref. 

No.

Part No.

Part Description

1.

784-5648

Frame Cover

2.

710-1652

Tap Screw 1/4-20 x .625

3.

748-0190

Spacer .508 ID x .75 OD 

4.

732-0264

Extension Spring

5.

712-0711

Jam Nut 3/8-24

6.

736-0105

Bell Washer .401 ID x .87 OD 

7.

684-0021

Friction Whl Support Bracket

8.

746-0898

Drive Cable 39.88”

9.

656-0012A

Friction Disc

10.

784-5689A

Front Support Guide Bracket

11.

713-0413

10T Sprocket

12.

746-0897

Auger Cable 44.75”

13.

750-0997

Spacer .675 ID x 1” OD

14.

711-1042

Hex Track Shaft

15.

684-0042C

Friction Wheel Assembly

16.

736-0160

Flat Washer .536 ID x .93 OD

17.

714-0474

Cotter Pin

18.

741-0563

Ball Bearing

19.

736-0242

Bell Washer .34 ID x .872 OD

20.

710-0538

Hex Cap Screw 5/16-18 x .625

21.

710-0857

Tap Screw 1/4-20 x .75

22.

736-0270

Bell Washer .265 ID x .75 OD 

23.

736-0176

Flat Washer 1/4 ID x .93 OD

24.

741-1111

Hex Flange Bearing

25.

710-0643

Hex Cap Screw 5/16-18 x 1”

26.

748-0234

Shoulder Spacer

27.

710-0604A

Tap Screw 5/16-18 x .625

28.

684-0031

Frame Assembly

29.

738-0924

Hex Screw 1/4-28 x .375

30.

756-0625

Cable Roller

31.

784-5688

Drive Cable Guide Bracket

32.

710-0599

Tap Screw 1/4-20 x .5

33.

784-5590

Shift Frame Bracket

34.

684-0014B

Shift Rod Assembly

35.

784-5687A

Auger Cable Guide Bracket

36.

710-0809

Tap Screw 1/4-20 x 1.250

37.

618-0063A

Friction Wheel Bearing

38.

718-0301A

Friction Wheel Hub

39.

735-0243B

Friction Wheel Rubber

40.

790-00011

Friction Plate

41.

790-00010

Friction Plate

Ref. 

No.

Part No.

Part Description

NOTE: For painted parts, please refer to
the list of color codes below. Please add
the applicable color code, wherever
needed, to the part number to order a
replacement part. For instance, if a part
numbered 700-xxxx is painted Yard-Man
Green, the part number to order would be
700-xxxx-0665.

Yard-Man Green: 0665

Yard-Man Yellow: 0674

Powder Black: 0637

Содержание 31BH763G401





























Отзывы: