background image

15

Model 107

Ref. No.

Part No.

Description

1.

647-0004

Control Handle Assembly

2.

710-1270

Oval C-Sunk Screw

3.

712-0324

Hex Lock Nut

4.

746-0883

Control Housing

5.

720-0295

Foam Grip

6.

749-0705A

Upper Handle

7.

710-1205

Rope Guide

8.

710-1174

Carriage Bolt

9.

749-0928

Lower Handle

10.

720-0279

Wing Nut

11.

720-0284

Hand Knob

12.

714-0104

Hairpin Clip

13.

746-0554

Control Cable 40.5”

15.

726-0240

Cable Tie

16.

17098

Hinge Clip

17.

731-0872A

Trail Shield

18.

682-0139

Cutting Deck Assembly: 20”

19.

736-0105

Bell Washer

20.

720-0426

Knob: Height Adjustment

21.

732-0404

Lever: Spring

22.

734-2004A

Wheel Assembly

23.

736-0504

Wave Washer

24.

738-0102

Axle Bolt

25.

731-1426

Hubcap: Radial Spoke, Yellow

26.

738-0507B

Shoulder Bolt

27.

15262B

Pivot Bar

28.

682-3024

Handle Bracket Assembly RH

682-3025

Handle Bracket Assembly LH*

29.

738-0585

Stake Bolt

30.

732-0731

Torsion Spring

31.

14578

Height Adjust. Assembly RH

14579

Height Adjust. Assembly LH*

32.

782-7006

Mounting Bracket

33.

736-0270

Bell Washer

34.

710-0599

Hex Washer Hd. TT Screw

35.

710-0654A

TT Sems Screw

36.

731-1409

Chute Deflector

37.

682-7002

Mulching Plug Assembly

38.

712-0431

Hex Lock Nut

39.

15261A

Height Adjustment Plate

40.

731-1933

Cover: Front End

41.

748-0376C

Blade Adapter

753-0588

Blade Adapter Kit (for service)

42.

742-0740

20” Mulching Blade

43.

736-0524A

Blade Bell Support

44.

710-1044

Hex Bolt

45.

747-0710

Hinge Pin

46.

736-0451

Saddle Washer

Ref. No.

Part No.

Description

* Not shown in Illustration on previous page

NOTE: For painted parts, please refer to
the list of color codes below. Please add
the applicable color code, wherever
needed, to the part number to order a
replacement part. For instance, if a part
numbered 700-xxxx is painted Yard-Man
Green, the part number to order would be
700-xxxx-0665.

Yard-Man Green: 0665

Yard-Man Yellow: 0674

Powder Black: 0637

Содержание 107

















Отзывы: