Yard Machines 580 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

background image

21

•

Lift and stabilize the front of the deck.

•

Loosen the center hex bolt and lower the blade and engine pulley until there is adequate clearance to move

the belt past the belt keeper.

•

Remove the belt from the engine pulley and around the blade. See Figure 21.

•

Reassemble in reverse order with new belt (part # 754-0465). NOTE: Begin idler reassembly by inserting bolt

up through the idler bracket hole. Adjust the drive clutch following instructions on page 16 of this manual.

IMPORTANT: Torque center hex bolt to between 450 and 600 in. lbs.

Figure 21

Maintaining Engine

Refer to the separate engine manual for engine maintenance instructions.

•

Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow

instructions carefully.

•

Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty

conditions. Poor engine performance and flooding usually indicates that the air cleaner should be serviced.
To service the air cleaner, refer to the separate engine manual packed with your unit.

•

The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is

recommended at the start of each mowing season; check engine manual for correct plug type and gap
specifications.

•

Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to

permit proper air circulation which is essential to engine performance and life. Be certain to remove all grass,
dirt and combustible debris from muffler area.

SECTION 13: OFF-SEASON STORAGE

The following steps should be taken to prepare lawn mower for storage if it will not be used for 30 days or more.
Compliance with these instructions will ensure that your mower will work properly when it is reused next season.

•

Clean and lubricate mower thoroughly as described in the lubrication instructions.

•

Refer to engine manual for correct engine storage instructions.

•

Coat mower’s cutting blade with chassis grease to prevent rusting.

•

Store mower in a dry, clean area. Do not store next to corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in a poorly ventilated or metal storage shed, care should be taken
to rust-proof the equipment. Using a light oil or silicone, coat the equipment, especially cable and all moving parts.

Remove belt

Engine

Pulley

Left Front
Wheel

Right Front
Wheel

from around
pulley and blade

Center

Hex Bolt

«
...
19
20
21
22
23
...
»

Содержание 580 Series





























Отзывы:

Нет отзывов

Похожие инструкции для 580 Series

Бренд: Thomsen Страницы: 6

Бренд: Texas Equipment Страницы: 36

EDGE HOG LE750 5

Бренд: Black & Decker Страницы: 7

Бренд: RedMax Страницы: 26

Бренд: Mantis Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды