Yard Machines 580 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 28

background image

11

•

Install the other wheel assembly and the other end of the axle shaft in the same way.

•

Remove the blocks from the rear of the mower and place the rear height adjusters in the same relative

position as the two front height adjusters.

Attaching Starter Rope

NOTE: The rope guide is already attached to the right side of the upper handle of your mower.

•

With the spark plug wire disconnected and grounded, hold the blade control handle against the upper

handle, and pull the starter rope out of the engine.

•

Slip the rope through the rope guide. See Figure 9. Tighten the wing nut holding the rope guide to the

upper handle.

Figure 9

Chute Deflector

The chute deflector is held in an upright position during shipping by means of a retainer. Remove this retainer
following the steps below.

•

Lift the spring-loaded chute up towards the engine and remove the retainer. Lower the chute carefully into

the operating position keeping fingers out of the way.

WARNING: The chute retainer is used for shipping purposes only. It must be removed from the chute
deflector and discarded before operating the mower.

Figure 10

Installing Mulching Baffle (Optional)

A mulching kit (OEM 190-110) is available for the mowers shown in this manual. To obtain a mulching kit,
contact the local retailer or service dealer. Some lawn mower models covered in this manual may already be
equipped with the optional mulching baffle. If yours is one of these, install the baffle following the steps below.

•

Lift the chute deflector up and slide the notches at the bottom of the mulching baffle over the lip of the

discharge opening. See Figure 11.

Wing Nut

Rope Guide

Chute Deflector

Chute Retainer

«
...
9
10
11
12
13
...
»

Содержание 580 Series





























Отзывы:

Нет отзывов

Похожие инструкции для 580 Series

Бренд: SNOWJOE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды