120v
LITHIUM-ION
TM
4
5
PRODUCT DESCRIPTION AND
SPECIFICATIONS
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save these instructions for later use.
Use the
Charger only when you fully understand and can
perform all functions without limitation, or have
received appropriate instructions.
SAFETY NOTES
1. Use only Yard Force 120V Li-ion battery
pack Y0L120BAT2.5. Do not use the original
charger on other li-ion batteries or on any
other type of battery—fire or explosion may
occur.
2. Check the battery charger, cable and plug
each time before using. Do not use the
battery charger when defects are detected.
Do not open the battery charger yourself and
have it repaired only by qualified personnel
using original spare parts.
3. The charger is designed to use standard
household 100-120 V~ 50/60Hz power
source. The charger's plug must match the
outlet. Never modify the plug in any way.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
4. Do not abuse the cord of charger. Never use
the cord for carrying, pulling or unplugging
the charger. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
5. Make sure the charger cord is located so
that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
6. Keep the battery charger clean.
Contamination may cause the danger of
electric shock.
7. Protect the battery charger away from rain
and moisture. The penetration of water in a
battery charger increases the risk of electric
shock.
8. Do not operate the battery charger on easily
inflammable surfaces (e.g. paper, textiles,
etc.) or in combustible environments. There
is danger of fire due to the heating of the
battery charger during charging.
9. The temperature range over which the battery
pack can be charged is typically from 41° F
to 113° F. Therefore, charging efforts outside
the prescribed temperature range may
automatically be blocked by the protection
circuitry of the battery pack. Longest life and
best performance can be obtained if the
battery pack is charged in the normal room
condition.
10. Disconnect charger from the power supply
when not in use. This will reduce the risk of
electric shock or damage to the charger if
metal items should fall into the opening.
11. This tool is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
12. Cleaning and user maintenance of the battery
charger shall not be made by children without
supervision.
OPERATION
Note:
- A new battery pack is supplied partially
charged.To ensure the best performance,
charge the battery completely before first
use.
- Make sure the main voltage is the same as
rating label which is located on the charger.
- Remove the battery pack from the charger
after it has been fully charged.
1. Connect the charger to a power supply. The
red LED light on the charger will be on.
2. To insert the battery pack into the charger,
align the grooves on the battery pack with
the raised ribs in the opening of the charger.
Then press the battery pack downward with
a moderate force. (There is a carrying handle
at the top of the battery pack. Lift the handle
up for easy-transporting.)
3. Once the battery pack is correctly located
in the charger, the green LED light of the
charger will flash continuously during normal
charging, while the red LED light is still on.
4. When charging is complete, both green and
red LED light of the charger will be on.
5. If you encounter one of following kind of
situations, the red LED light of charger will
flash.
- Wrong communication. It refers to poor
connection between charger and battery
pack.
- Faulty with battery pack. It need be repaired
by the customer service center.
Wall-mount holes
The charger has hanging holes for convenient
storage. Install two screws horizontally in the
wall 4.2" (10.7cm) apart. Use screws sufficiently
strong to hold the combined weight of the
charger and battery pack.
MAINTENANCE AND SERVICE
- Occasionally clean the charger using a soft,
clean and dry brush.
When the charger is no longer operative, please
refer to an authorized after-sales service centre.
DISPOSAL
Battery chargers, accessories and packaging
should be sorted for environmental-friendly
recycling.
Do not dispose of battery chargers into household
waste!
4.2" (10.7cm)
