background image

 

What to Do and Not to Do 

 

 

Keep the generator outside. Never use it indoors. (unless properly 
installed inside building). 

 

Install a battery-operated carbon monoxide alarm.  

 

Keep the generator dry. Do not use in wet conditions. To protect from 
moisture, operate it on a dry surface and with adequate ventilation.  

 

Dry your hands if wet before touching the generator.  

 

Never

 

try to power the house wiring by plugging the generator into a 

wall outlet, a practice known as "backfeeding". This is an extremely 
dangerous practice that presents an electrocution risk. It also bypasses 
some of the built-in household circuit protection devices unless done 
properlly. 

 

If you must connect the generator to the house wiring to power 
appliances, 

get a licensed electrical contractor to do it 

in 

accordance with 

Australian Standards AS/NZS 3000 Electrical 

Installations

.  

 

Avoid creating a fire hazard. Store fuel for your generator in properly 
labelled non-glass safety containers, out of the home and away from 
fuel-burning / heat appliances.  

 

Before refueling the generator, turn it off and let it cool down. Fuel 
spilt on hot engine parts could ignite.  

 

When running generator on hand ensure all load connection devices 
are removed. 

 

When performing service work ensure emergency stop button is 
pressed. 

 

Do not smoke in or around generator 

 

Do not run generator on light loads for prolonged periods of time, the 
generator needs at least 50% loading to prevent damage.  

 

Familise yourself with all paperwork / manuals available to you. 

 

Ensure emergency button is out prior to starting generator. 

 

Contact installer For More Details 

 

 
 

 

24

Содержание TNE Series



























Отзывы: