Yanmar 3YM30 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 231

background image

6. Fuel injection equipment

140

6.1.4 Removing a fuel injection pump

The procedure to remove a fuel injection pump from the gear case is shown.

[NOTICE]

Be sure to remove a flange and a fuel injection pump

drive gear with a pair without loosening the flange

bolts.

1) Remove fuel injection pipes, fuel pipes and a

remote control wire. Block the entrance with tape

so that trash may not enter the fuel injection pipes

and the fuel injection pump.

2) Mark the position of the timing marks of a fuel

pump and a gear case. Or, put a mark on the

gear case at the position to agree the timing mark

of a fuel pump.

3) Remove a pump cover from the gear case.
4) Give the marks on a fuel injection pump drive gear

and a idle gear with paint or the like.

5) Loosen fuel injection pump installation nuts (three nuts).
6) Loosen a installation nut of a fuel injection pump drive gear.
7) Pull a fuel injection pump drive gear and a flange with a pair to your side by gear puller.
8) Remove a pump drive gear nut and a washer.
9) Remove a fuel injection pump. Leave the pump drive gear in the gear case.

6.1.5 Installing a fuel injection pump

[NOTICE]

• Use a new O-ring on the fuel pump flange and apply grease.

• Confirm whether the marks of the pump drive gear and the idle gear is correct.

1) Turn a camshaft so that the key of the pump camshaft may almost agree in a position of the key

groove of a pump drive gear.

2) Insert a fuel injection pump into the installation hole of the gear case straight to prevent the

damage of the O-ring. Insert a fuel pump while confirming whether the key of a camshaft and the

key groove of a drive gear agree.

3) Assemble a pump drive gear nut and a washer together temporarily.
4) Turn a fuel injection pump to the position where the marks of the fuel injection pump and the gear

case agrees.

5) Fasten pump installation nuts (three nuts) on the fuel injection pump.
6) Tighten the pump installation nut by the specified standard torque.

Tightening torque of the pump drive gear nut (without lube oil)

6.1.6 Adjusting fuel injection timing

Refer to 2.2.6(1) in chapter 2.

Tightening torque

N•m(kgf•m)

58.8-68.8 (6.0-7.0)

Fuel injection pump

Flange

Flange bolt

Spring

washer

Pump drive gear nut

Fuel injection pump

drive gear

Don't disassemble

«
...
159
160
161
162
163
...
»

Содержание 3YM30








































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3YM30

Бренд: J.A.P Страницы: 21

Бренд: Hyster Страницы: 25

MAX-61SX-H RING WC Series

Бренд: O.S. engine Страницы: 36

Бренд: FAAC Страницы: 22

LYCOMING 200-6XL Series

Бренд: E-MAG Страницы: 30

Бренд: V2 Страницы: 17

Diesel Stage 2 Boost Cooler

Бренд: Snow Performance Страницы: 20

Бренд: DLE Страницы: 4

Бренд: Honda Страницы: 12

Бренд: Honda Страницы: 57

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 2

O.S.MOTOR OMH-5830-490

Бренд: O.S. engine Страницы: 2

O.S.MOTOR OMA-2820-950

Бренд: O.S. engine Страницы: 2

MAX-46FX-Hring Series

Бренд: O.S. engine Страницы: 30

Бренд: O.S. engine Страницы: 29

Бренд: Krick Страницы: 12

Бренд: Ingersoll-Rand Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды