Yancheng Tractor Factory Jinma 200 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 52

background image

Jinma 200 series Tractor Users Manual

MCE 2004.01

INTRODUCTION

This manual is a general guide to provide the user with general information with
respect to personnel and  equipment safety, operational procedures and
maintenance of your machine.
This manual was developed to fill the requirement for a JINMA specific operations
and maintenance manual.  While Jinma tractors come with a set of 4 manuals,
some of the language syntax is a little hard to follow.

Sources of data

Sources of data for this manual come from many places. They include , but are
not limited to the following:

http://www.johnstractor.homestead.com/,

http://www.emerybuilt.com/

http://www.tractor-outlet.com/

http://www.china-tractors.com/

http://www.tractorpages.com/,

http://chinabestproducts.com

Factory Engine Operations Manual,
Factory Tractor Operations and Maintenance Manual,
Factory Tractor Illustrated Parts Breakdown Manual,
Factory Engine Illustrated Parts Breakdown Manual.

The Chinese Tractor Owner Association is a good place to lurk, ask questions and
get/give support from/to others.

http://www.ctoa.net

Please read this manual carefully and keep in a convenient place for future

reference.

Do not hesitate to contact your local dealer for any questions concerning

the tractor. Even if you obtained this tractor as a crate assembly project, a

tractor dealer can provide skilled personnel, spare parts and all tools and
equipment necessary for your service requirements. Most of all, a dealer will
have the experience of working with tractors and small diesel engines.

PARTS

Parts are readily available for JINMA series tractors. The Internet is a good place
to find sources of parts.

http://www.jinmaparts.com

is but one company selling

parts for your machine.
Any suggestions and or comments about this manuals contents, errors or
omissions are most welcome. Please email or mail:

Steven Bradshaw
1033 Braithwaite Drive
Cobble Hill, BC
Canada. V0R1L0
[email protected]

Version 0.2

Page 7 of 52

«
...
5
6
7
8
9
...
»

Содержание Jinma 200 Series





















































Отзывы:

Нет отзывов

Похожие инструкции для Jinma 200 Series

Бренд: Bad Boy Страницы: 144

Бренд: R2 RINALDI Страницы: 26

Бренд: Yanmar Страницы: 16

Бренд: Pasquali Страницы: 65

Бренд: SaMASZ Страницы: 27

Бренд: Kubota Страницы: 6

Бренд: KitchenAid Страницы: 6

Бренд: KitchenAid Страницы: 7

Бренд: KitchenAid Страницы: 6

Бренд: KitchenAid Страницы: 6

5400 BROCHURE 86-112

Бренд: MASSEY FERGUSON Страницы: 13

Kubota F 80 Series

Бренд: Tiktite Страницы: 24

Бренд: Sears Страницы: 19

Бренд: Sears Страницы: 36

Бренд: hillvert Страницы: 7

Бренд: Fox Страницы: 20

Бренд: Euro Shatal Страницы: 22

Extreme Stiff Arm Backhoe

Бренд: Carolina Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды