Yamato Pure Line WL220T Скачать руководство пользователя страница 8

Страница: 8 / 44

2. Before operating the unit

Installing procedures and preparation before operation

Warning

1. Be sure to connect the earth wire.

・

Be sure to connect the earth wire (green wire of the power cord) to the earth wire or to
the earth terminal.

・

Never connect the earth wire to the gas pipe or water pipe, in order to prevent fire.

・

The earth wire must never be used for grounding of the telephone line and lightning
arrestor. This is to prevent fire and electric shock.

・

Never use the branch socket outlet because it causes hazardous heat generation.

Used of ground socket outlet recommended

When using a diode socket outlet

When there is no ground terminal.

●

In this case, class D grounding work is

necessary and please consult your dealer or
our customer service center.

Ground adaptor

●

Insert the ground adaptor into a power plug

confirming the polarity of the outlet. Connect
the grounding wire (green) of the ground
adaptor to the ground terminal on the power
supply equipment

。

2. Carefully select an installation site.

Take special care not to install the
unit at a place described below:

・

Uneven surfaces or dirty surfaces

・

Where flammable gas or corrosive

gas exists

・

Where the ambient temperature is

℃

or less

・

Where the ambient temperature is

℃

or more

・

Where temperature changes

severely

・

Where dusty and humidity is high

・

Where subject to direct sunlight

・

Where vibration is severe

・

Where unstable power supply

・

Where uneven floor

（

within

reference

3 degree

）

・

Where raw water pressure is high

・

Where with raw water pressure is

low

・

Outdoors

・

At a place lower than the suction

port of the constant temperature
and humidity chamber

・

On a device or a laboratory table

(with locked adjusters, etc.)

It is recommended to secure the space of the range wider than the one shown above around
the product.

Toward front
by 30cm or more

10cm or more

3-pole power plug with an

earth terminal

Earth wire

3-pole power plug with an

earth terminal

ｗ

Earth pole

10cm or more

Содержание Pure Line WL220T













































Результаты поиска

Содержание Pure Line WL220T

Отзывы:

Бренды по названию

Популярные бренды

Yamato Pure Line WL220T, Инструкция по эксплуатации

Результаты поиска

Содержание Pure Line WL220T

Отзывы:

Бренды по названию

Популярные бренды