background image

 

 

51 

 

Handling Precautions 

 

 

WARNING! 

If a problem occurs 

 

If  smoke  or  strange  odor  should  come  out  of  this  unit  for  some  reason,  turn  off  the  power  key 
right  away,  and  then  turn  off  the  circuit  breaker  and  the  main  power.    Immediately  contact  a 
service  technician  for  inspection.  If  this  procedure  is  not  followed,  fire  or  electrical  shock  may 
result. Never perform repair work yourself, since it is dangerous and not recommended.

 

Substances that cannot be used 

 

Never  use  explosive  substances,  flammable  substances  and  substances  that  include  explosive 
or  flammable  ingredients  in  this  unit.  Explosion  or  fire  may  occur.  (Refer  to  page  62  "List  of 
Dangerous Substances"
.)

 

 

CAUTION! 

Do not step on this unit 

 

Do not step on this unit. It will cause injury if this unit fall down or break.

 

Do not put anything on this unit 

 

Keep  clear  on  the  unit  to  prevent  dropping  and  injury.    Do  not  put  flammable  such  as  paper 
around it.

 

During a thunder storm 

 

During a thunderstorm, turn off

 

the power key immediately, then turn off the circuit breaker and 

the main power.    If this procedure is not followed, fire or electrical shock may be caused.

 

About the amount of samples 

 

If  the  excessive  amount  of  sample  is  set,  it  could  be  impossible  to  control  the  temperature 
normally. To keep the temperature control accuracy, do not use this unit in overload.

 

Recovering after power failure 

 

When power is supplied after a power failure, the device automatically starts operation again with 
the same state as just before the power failure.   

When I used a backup power supply for blackout return, but a blackout occurred for need in less 
than 30 minutes more than 30 minutes as for the charge time of the backup power supply since I 
turned on electricity in a device, there is the thing that a blackout does not return temporarily. The 
blackout return function operates normally after it was charged a backup power supply enough 
because I am not abnormal.

 

Содержание IN604W



































































Отзывы: