Yamato IN604W Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 66

Yamato IN604W Скачать руководство пользователя страница 18

15

Operation Method

Fixed Temperature Operation

3

Set temperature

①

The

setting

temperature

input

screen

is

displayed. The Sub Display indicates "Set
TEMP" and the numeric character that indicates
temperature blinks.

②

Set the temperature using the "

▲▼

".

③

Press the ENTER key to decide the temperature

and start the fixed temperature operation.

CAUTION!



The refrigerator operation can not be performed

again for five minutes just after an operation stop.
The refrigerator has been in the standby state and
the REFRIGE lamp blinks during the period.

4

Start operation

①

The blinking FIXED TEMP lamp lights on when

the  fixed  temperature  operation  starts.    The  unit
starts  to  control  temperature  according  to  the
setting  temperature.      The  HEATER  lamp  lights
on when the heater is on and The REFRIGE lamp
lights on when the refrigerator is on.

②

The Sub Display displays the setting temperature.

The  arrow  which  indicates  the  state  of
temperature  control  is  also  displayed  with
blinking.    The  direction  of  arrow  shows  as
follows  depending  on  the  relation  between  the
setting  temperature  at  operation  start  and  that  in
furnace.

Set TEMP

37.0

℃↑

2002/01/01 12:00

Set TEMP

37.0

℃↓

2002/01/01 12:00

(When setting temperature is
higher than temperature in
furnace)

(When setting temperature is
lower than temperature in
furnace)

③

The direction of arrow shows as shown below

when the temperature in furnace reaches to
within

±

1.0

℃

of setting temperature.

Set TEMP

37.0

℃→

2002/01/01 12:00

(When temperature in furnace
reaches to around setting
temperature)

POWER

④

Press the POWER key to stop operation.

«
...
16
17
18
19
20
...
»

Содержание IN604W



































































Отзывы:

Нет отзывов