manualshive.com logo in svg

YAMARIN 68 Cabin, Руководство пользователя

Поделиться
Скачать
YAMARIN 68 Cabin Скачать руководство пользователя страница 28

YAMARIN 68 Cabin 

 

 

28 (39) 

 

 

 

 

 
Tie the boat properly before starting the transport. Fastening belts located at  the bow should 
be directed "down-back" and fastening belts located at rear should be directed "down-front".  
Do not leave any loose equipment or extra load to boat when it's transported. Take seat 
cushion away and close the hatches properly. 
 
When transporting the boat the motor should be on its driving position. Make sure that there 
is the needed road clearance.  
 
The fastening belts must be loosened up if the boat is kept on trailer between transportations 
and tightened up before next transportation. 
 
 

NOTE! 

 

The trailer should be a little front-weighted. Make sure that the 

 

 

 

boat is fasten tight enough to trailer and the weight of 

the boat is    

 

divided equally on the both side supports. If the boat 

swings  

 

 

against the side support it can damage the hull. 

 
When letting down the boat from trailer, remember to fasten the bow rope to the boat in order 
to release cable from the trailer hook when boat is on the water. Look out the winch handle! 

Содержание 68 Cabin








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды