Yamaha Z200 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 98

Yamaha Z200 Скачать руководство пользователя страница 87

Trouble Recovery

81

gine is running.

EMU29670

Engine fails to operate

EMU29741

Low oil level warning activates

If the oil level is allowed to drop too low, the
red segment will appear on the oil level indi-
cator, the buzzer will sound, and engine
speed will be limited to about 2000 r/min. If
this happens, a reserve amount of oil can be
pumped from the remote oil tank to the en-
gine oil tank using the emergency switch.

WARNING

EWM01050

Be sure to stop the engine before per-

forming this procedure.

CAUTION:

ECM00900

●

If the emergency switch is held up too
long, too much oil will be pumped into
the engine oil tank, overflowing it. Re-
lease the switch when oil reaches the
upper level line on the engine oil tank.

●

Do not use this emergency procedure
unless the oil level warning indicators

are working.

1.

Remove the top cowling.

2.

Turn on the main switch.

3.

Lift the emergency switch to pump re-
serve oil into the engine oil tank from the
remote oil tank.

4.

After using the emergency switch, turn
off the main switch, then turn it back on.
This resets the warning system to nor-

ZMU04444

1. Emergency switch

1. Engine oil tank
2. Remote oil tank

ON START

OFF

ZMU01906

1

ZMU04010

1

2

ZMU01908

«
...
85
86
87
88
89
...
»

Содержание Z200



































































































Отзывы:

Нет отзывов