manualshive.com logo in svg

Yamaha YZFR6X(C) 2008, Руководство по обслуживанию

Yamaha YZFR6X(C) 2008 - спортивный мотоцикл с мощным двигателем и передовыми технологиями. Для обслуживания этого великолепного мотоцикла необходимо скачать бесплатное руководство по обслуживанию с manualshive.com. Не забудьте загрузить Service Manual прямо сейчас для поддержания своего мотоцикла в отличном состоянии!

Поделиться
Скачать
background image

CABLE ROUTING

2-52

1. Clutch cable
2. Throttle cable (return side)
3. Throttle cable (pull side)
4. Right handlebar switch lead
5. Right radiator cover
6. Right upper side cowling
7. Right coupler holder
8. Right radiator fan motor lead
9. TPS lead
10.Throttle servo motor lead
11.Accelerator position sensor lead
12.Pickup coil lead
13.Ignition coil lead
14.Throttle body lead
15.Intake funnel servo motor lead
16.Rear brake light switch lead
17.O

2

 sensor lead

18.EXUP servo motor lead
19.Neutral switch lead
20.Fuel pump coupler
21.Fuel sender coupler
22.Fuel tank breather hose
23.Fuel tank drain hose
24.Battery negative lead
25.Engine ground lead
26.Sub-wire harness (secondary injector)
27.Oil level switch lead
28.Sidestand switch lead
29.Speed sensor lead
30.Starter motor lead
31.Left radiator fan motor lead
32.Left coupler holder
33.Main switch lead
34.Left handlebar switch lead
35.Radiator plate
36.Frame
37.Main harness

A. Route the clutch cable above the cover and 

from the space next to the right coupler 
holder to bottom of the vehicle.

B. Make sure that the throttle cable is not 

twisted or crossed.

C. Route the throttle cable along the edge of 

the protector on the return side of the throt-
tle cable and fit in the clamp on the cable 
from upper side of the vehicle to the bot-
tom.

D. To the headlight.
E. Fasten the headlight harness and right 

front turn signal light lead at the positioning 
tape with a clamp.

F. To the front right turn signal light.
G. To the radiator.

H. Fasten the main harness, right radiator fan 

motor lead, throttle position sensor lead, 
throttle servo motor lead and accelerator 
position sensor lead with a plastic locking 
tie. Face the plastic locking tie to upward 
and insert it into the hole of the right cou-
pler holder.

I. Route the right radiator fan motor lead 

through the inside of the main harness. 
There is no order for placing the throttle 
position sensor lead and throttle servo 
motor lead.

J. To the engine.
K. To the throttle body.
L. To the coolant temperature sensor.
M. Route the coolant temperature sensor lead 

above the pickup coil lead, neutral switch 
lead, oil level switch lead and speed sensor 
lead.

N. Push the throttle body lead inward and 

place the ignition coil lead coupler so that it 
does not overlap or underlap with the throt-
tle body lead coupler.

O. The oil level switch lead, speed sensor 

lead, pickup coil lead coupler and intake 
funnel servo motor lead coupler should be 
at inner and under the main harness. 
There is no order for placing the neutral 
switch lead.

P. Insert the plastic locking tie on the main 

harness to the hole of the frame securely 
so that it does not float.

Q. Route the neutral switch lead between the 

frame and engine.

R. To the rear fender.
S. Install both the negative battery lead and 

engine ground lead to the crankcase with 
the bolt. There is no order for placing the 
leads and install so that projection on each 
lead are facing up. Route the oil level 
switch lead and speed sensor lead under 
the negative battery lead and engine 
ground lead.

T. Sub-wire harness (secondary injector) 

coupler must be under the main harness.

U. To the secondary injector.
V. Fasten the main harness and left radiator 

fan motor lead with a plastic locking tie. 
Face the tip of the plastic locking tie to 
upward and insert it into the hole of the left 
coupler holder.

W. Face the end of the plastic locking tie 

inward, route the hole of the rectifier/regu-
lator bracket, then fasten the main har-
ness.

X. When turning the handle fullest to the right, 

make sure that the left handlebar switch 
lead is not strained.

Y. The left handlebar switch lead and main 

switch lead can either be on top or bottom.

Z. Route the throttle cable through the right 

side of the rib on the plate above the radia-
tor. Make sure that it is not twisted.

Содержание YZFR6X(C) 2008



















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR6X(C) 2008

Kappa K132 Manual preview
K132
Бренд: Kappa Страницы: 4
Yamaha FZ6-SS Service Manual preview
FZ6-SS
Бренд: Yamaha Страницы: 435
Kabuto FR-1 Instruction Manual preview
FR-1
Бренд: Kabuto Страницы: 12
GAS GAS EX 450F 2021 Owner'S Manual preview
EX 450F 2021
Бренд: GAS GAS Страницы: 142
R&G FI0056BK Fitting Instructions preview
FI0056BK
Бренд: R&G Страницы: 4
BMW K 1600 GTL Rider'S Manual preview
K 1600 GTL
Бренд: BMW Страницы: 176
GYS 037281 User Manual preview
037281
Бренд: GYS Страницы: 36
Paaschburg & Wunderlich SHIN YO TEXAS Mounting And Safety Instructions preview
SHIN YO TEXAS
Бренд: Paaschburg & Wunderlich Страницы: 2
SRC KTM390-14-01-SL Quick Start Manual preview
KTM390-14-01-SL
Бренд: SRC Страницы: 4
Honda XL125LK Owner'S Manual preview
XL125LK
Бренд: Honda Страницы: 243
NEO TOOLS 97-590 Instruction Manual preview
97-590
Бренд: NEO TOOLS Страницы: 8
Triumph Daytona 675 2014 Owner'S Handbook Manual preview
Daytona 675 2014
Бренд: Triumph Страницы: 162
Yamaha XV19CSD Owner'S Manual preview
XV19CSD
Бренд: Yamaha Страницы: 96
Yamaha XV17AWZ Owner'S Manual preview
XV17AWZ
Бренд: Yamaha Страницы: 110
Yamaha Tenere 700 2021 Owner'S Manual preview
Tenere 700 2021
Бренд: Yamaha Страницы: 112
Yamaha Tenere 700 2023 Owner'S Manual preview
Tenere 700 2023
Бренд: Yamaha Страницы: 114
Yamaha Super Tenere ES 2023 Owner'S Manual preview
Super Tenere ES 2023
Бренд: Yamaha Страницы: 132
Yamaha Tenere 700 2020 Service Manual preview
Tenere 700 2020
Бренд: Yamaha Страницы: 472

Бренды по названию

Популярные бренды

Загрузить еще бренды