Yamaha YZFR6W Скачать руководство пользователя страница 31

Страница: 31 / 118

INSTRUMENT AND CONTROL FUNCTIONS

3-13

it by aligning a groove on the adjusting
knob with the “

” mark on the brake

lever.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13070

Fuel tank cap

To open the fuel tank cap

Open the fuel tank cap lock cover, in-
sert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.

To close the fuel tank cap

1. Push the fuel tank cap into position

with the key inserted in the lock.

2. Turn the key counterclockwise to

the original position, remove it, and
then close the lock cover.

1. Brake pedal

1. Fuel tank cap lock cover

2. Unlock.

U2C011E0.book Page 13 Wednesday, July 12, 2006 10:13 AM

Содержание YZFR6W























































































































Результаты поиска

Содержание YZFR6W

Отзывы:

Бренды по названию

Популярные бренды

Yamaha YZFR6W, Руководство пользователя

Результаты поиска

Содержание YZFR6W

Отзывы:

Бренды по названию

Популярные бренды