manualshive.com logo in svg

Yamaha YZF600RT, Руководство пользователя, Страница: 70 / 105

Поделиться
Скачать
Yamaha YZF600RT Скачать руководство пользователя страница 70

PERIODIC MAINTENANCE AND MINOR REPAIR

6-29

6

NOTE:

Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same po-
sition for proper wheel alignment.

CAUTION:

ECA10570

Improper drive chain slack will over-
load the engine as well as other vital
parts of the motorcycle and can lead
to chain slippage or breakage. To
prevent this from occurring, keep
the drive chain slack within the
specified limits.

3. Tighten the locknuts, and then

tighten the axle nut to the specified
torque.

EAU23021

Lubricating the drive chain 

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

CAUTION:

ECA10581

The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.

1. Clean the drive chain with kero-

sene and a small soft brush.

CAUTION:

ECA11120

To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

1. Axle nut

2. Alignment marks
3. Drive chain slack adjusting nut

4. Locknut

Tightening torque:

Axle nut:

117 Nm (11.7 m·kgf, 85 ft·lbf)

U5AH19E0.book  Page 29  Thursday, May 13, 2004  4:23 AM

Содержание YZF600RT










































































































Отзывы:

Нет отзывов