Yamaha YZ 2023 Series Скачать руководство пользователя страница 302

Страница: 302 / 378

SIGNALING SYSTEM

8-15

EAM30349

TROUBLESHOOTING

•

The fuel level warning light does not come on.

TIP

Before troubleshooting, remove the following part(s):
1. Seat
2. Side cover (left/right)
3. Air scoop (left/right)
4. Fuel tank

Check the signaling system

The fuel level warning light fails to come on.

1. Check the fuse.

Refer to “CHECKING THE FUSES”

on page 8-49.



Replace the fuse(s).



2. Check the battery.

Refer to “CHECKING AND

CHARGING THE BATTERY” on

page 8-50.



•

Clean the battery terminals.

•

Recharge or replace the battery.



3. Check the main relay.

Refer to “CHECKING THE RE-

LAYS” on page 8-51.



Replace the main relay.



4. Check the entire signaling system’s

wiring.

Refer to “CIRCUIT DIAGRAM” on

page 8-13.



Properly connect or repair the signaling

system’s wiring.



This circuit is OK.

1. Check the fuel level warning light

bulb and socket.

Refer to “CHECKING THE BULBS

AND BULB SOCKETS” on page

8-49.



Replace the fuel level warning light bulb,

socket or both.



2. Check the fuel sender.

Refer to “CHECKING THE FUEL

SENDER” on page 8-56.



Replace the fuel pump assembly.



3. Check the resistor.

Refer to “CHECKING THE RESIS-

TOR” on page 8-56.



Replace the resistor.



Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды