Yamaha YP125R Скачать руководство пользователя

Страница: 191 / 498

REAR WHEEL

4-16

EAS28760

REMOVING THE REAR WHEEL

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

TIP

Place the vehicle on the centerstand so that the
rear wheel is elevated. Also, place a suitable
stand under the engine.

EAS22090

CHECKING THE REAR WHEEL

1. Check:

• Tire
• Rear wheel

Damage/wear

→

Replace.

Refer to “CHECKING THE TIRES” on page
3-39 and “CHECKING THE WHEELS” on
page 3-41.

2. Measure:

• Radial wheel runout
• Lateral wheel runout

Refer to “CHECKING THE FRONT WHEEL”
on page 4-11.

EAS22150

ADJUSTING THE REAR WHEEL STATIC
BALANCE

TIP

• After replacing the tire, wheel or both, the rear

wheel static balance should be adjusted.

• Adjust the rear wheel static balance with the

brake disc installed.

1. Adjust:

• Rear wheel static balance

Refer to “ADJUSTING THE FRONT WHEEL
STATIC BALANCE” on page 4-12.

EAS28770

INSTALLING THE REAR WHEEL (REAR
BRAKE DISC)

1. Install:

• Rear brake disc

TIP

Tighten the brake disc bolts in stages and in a
crisscross pattern.

2. Check:

• Rear brake disc

Refer to “CHECKING THE REAR BRAKE
DISC” on page 4-37.

3. Install:

• Rear fender
• Air filter case mounting bolts

TIP

Place the rear fender between the air filter case
and the crankcase, and then install the air filter
case mounting bolts.

Radial wheel runout limit

1.0 mm (0.04 in)

Lateral wheel runout limit

0.5 mm (0.02 in)

Rear brake disc bolt

23 Nm (2.3 m·kgf, 17 ft·lbf)
LOCTITE®

Air filter case mounting bolt

9 Nm (0.9 m·kgf, 6.5 ft·lbf)
LOCTITE®

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды